E4404 V2 The Federal Democratic Republic of Ethiopia MINISTRY OF INDUSTRY ENVIRONMENTAL SOCIAL IMPACT ASSESSMENT REPORT FOR BOLE LEMI II INDUSTRIAL ZONE COMPETITIVENESS AND JOB CREATION PROJECT (Draft Report) January 2014 Social and Environmental Impact Assessment Report Executive summary Introduction The Government of Ethiopia has in recent time given emphasis to ensuring faster and sustained development of the industry sector. It is making relentless efforts to implement its industrial growth and development plan which is also part of the current five years Growth and Transformation Plan (GTP). To this effect, the Government in association with the International Development Association (IDA) of the World Bank prepared Industrial zone Development Project (IZDP), which will be implemented with funds contributed by the Government, the IDA and other donors. IZDPs in collaboration with other partner are being implemented to specifically enhance the environmental, economic and social performance by utilizing available resources in an environmentally sustainable manner. The establishment of Industry zone development in potentially suitable towns and cities of the country has been found as the best option to promote industry development in the country. The Government has therefore identified five IZDPs sites in the cities of Addis Ababa, Awassa, Kombolcha and Dire Dawa. Bole Lemi Industrial Development project is one among the identified sites in the city of Addis Ababa. The development objective of the proposed IZDP is to contribute to job creation by attracting investments and improving enterprise competitiveness in the targeted industrial zones (IZs). This will be achieved by: (i) Strengthening institutional and regulatory framework for IZ development, and capacity building; (ii) Supporting industrial infrastructure development of IZs; and (iii)Enhancing IZ linkages to small and medium enterprises (SMEs) through targeted interventions. The Bole-Lemi Second Phase Industrial Zone Development Project to which the ESIA study will be conducted is expected to greatly contribute in the fulfilment of the above objective. Objectives and methodology for the preparation of ESIA The Project will trigger a couple of World Bank environmental safeguards policies including OP 4.01 on Environmental Assessment. The consultant carried out scoping and found the potential impact of this project to have significant effect on the biophysical and socio- economic environment and thus requiring the preparation of full ESIA in line with the World FDRE Ministry of Industry Page ii Social and Environmental Impact Assessment Report Bank’s environmental and social safeguards policies on Environmental and Social Impact Assessment (OP 4.01) and consistent with national laws. The purpose of the ESIA is:  to inform decision makers about environmental and social impacts (including possible land acquisition and resettlement) of the at the project planning phase ;  to bring into the attention of the planners and designers the magnitude of impacts and the possible alternative sites that can be considered to those minimize impacts;  to identify social and environmental impacts of the proposed development project and recommended appropriate mitigation measures; and  to prepare social and environmental management plan Preparation of the SEIA required review of previous studies relevant to the assignment and field work for making physical observation and consultation with the relevant stakeholders and the would be Project Affected Population (PAPs). To this effect the consultant reviewed the existing environmental policies and legislations as well as procedures and guidelines useful to undertake the ESIA study. Furthermore, previous studies related to the project as well relevant policies and regulatory frameworks of the Ethiopian Government and other international and bilateral policies and strategies including the World Bank Safeguard Policies has been reviewed. Consultations were also made at different levels including relevant personnel of the Ministry of Industry (MoI), Bole Sub-city and Woreda 11 in which the proposed IZ is located as follows. Consultation at the Government level: Meeting has been conducted with the personnel of relevant departments and directorate of the Ministry of Industry particularly the Industry Zone Development and Protection Directorate. In the absence of a fully fledged feasibility study, such meetings were very useful in clarifying the overall objectives of the project and preferred mixes of factories that would operate in the IZ and the required outputs and benefits the nation expects to achieve from implementing this project. Furthermore, consultations were made with the experts that assigned land. The expert in the Sub City clarified to the consultant the reason why they chose this site and further explained the criteria they used during the site selection process. The consultations made at the Woreda level (Woreda 11) were also very FDRE Ministry of Industry Page iii Social and Environmental Impact Assessment Report important for the understanding of the socioeconomic realities in the proposed Bole-Lemi Industrial Zone in terms of making an overall assessment on the population and settlements, livelihood, available public services and infrastructures and other social and economic activities and level of awareness of the community regarding the proposed project. Relevant line offices of the Woreda Administration were also consulted on issues such as dislocation and resettlement of PAPs, the readiness of relevant institutions to implement activities and assistances they can provide as per their mandates and responsible with respect resettlement and other related requirements. Consultations at the community level: Consultations and discussions have also been made with the PAPs and other community representatives such as the elderly, religious leaders. Objectives of the ESIA, potential positive and negative impacts, possible mitigation measures and the Environment and Social Management Plan (ESMP) were discussed and views and opinions gathered. Participants of the meeting in general supported the objectives and the construction and operation of the IZ. However, they couldn’t hide their fears and reservations about the resettlement and other supporting activities that need to be implemented by the Government. Further, they requested for the Government to make the necessary effort to provide adequate compensation to the affected population for the land and asset they will lose due to project implementation and also provide them the necessary assistance to make their life better off. Project Description and Justification The proposed Phase Two Bole Lemi Industry Zone Project is one of the industry zones to be developed in Addis Ababa city on a land area of about 183ha as part of the wider industrial growth development program of the country. A mix of factories will be operating within the IZ in 22 modern industrial sheds having two types of sizes of 5,777m2 and 11,217m2, with their common facility and parking area. The textile and leather factories are expected to use semi processed materials for nit to fit types of work therefore the factories will not be engaged in the dyeing and tanning processes which generally release heavy pollutants into the environment. The Industry Zone is expected to construct all on-site infrastructure works such as sanitary installation, electrical installation, domestic water supply system, fire hydrant, sewerage, Drainage as well as temporary storage for water and fuel. The IZ will also include the FDRE Ministry of Industry Page iv Social and Environmental Impact Assessment Report development of other infrastructures that will provide support for the day to day operation of greenery, parks, and recreational areas such as gymnasium and football field. Common shower and toilets will also provide in the factory buildings. Currently, the main agenda of the Federal Democratic Republic Government of Ethiopia is to eradicated poverty. One of the several strategic directions to realize this National agenda is to promote the industrialization process to play its role in the development of the country’s economy. The project is justified on the grounds that it will reduce the prevailing high unemployment rate while it will also address the trade deficit and lack of foreign exchange for importing required items and running development activities that rely heavily on imported technologies. Description of the Project Environment The proposed Bole-Lemi Industry Zone Development Project is located in the southwestern part of Addis Ababa City administration in Woreda 11 of Bole Sub-city. It is bounded by two rivers (Lemi and Weji) which drain to Big Akaki River locally known as Tiliku Akaki River. The topography is predominantly flat agricultural with elevation decreasing towards the two rivers. It is largely inhabited by people engaged in rural livelihood. Traditional mixed farming type of agriculture dominated by rain-fed farming is currently the most important economic activity in the three rural settlements (Menders) that will be affected by the establishment of the proposed industrial zone. Livestock ownership is comparatively low and is primarily geared towards owning some oxen and donkey needed for transporting and farming activities. Much of the area is allotted for crop production with very limited grazing land here and there. The area is virtually devoid of any natural vegetation such as trees and shrubs due to heavy encroachment from farming, grazing and establishment of numerous quarry and stone crusher plants. However, there are still eucalyptus trees in areas very close to the villages. There is no any designated sensitive area. Potential Positive Impacts and Enhancement Measures The anticipated major potential impacts of the proposed IZ are: FDRE Ministry of Industry Page v Social and Environmental Impact Assessment Report  Contributes to reduction of the prevailing high unemployment rate while it will also address the trade deficit and lack of foreign exchange for importing required items and running development activities that rely heavily on imported technology and facilities.  Local income generation and job creation for skilled, semiskilled and unskilled  Skill and knowledge transfer  Improved access to basic service  Increased land and asset value of the surroundings The above positive impacts can be enhanced by the implementation of various trainings that would enable the project affected population to be engaged in the different activities of the IZ. Furthermore, implementation of credit facilities and services that would enable them run their own businesses from the various service and market demands are anticipated to be created by the IZ. Potential Negative Impacts and Mitigation Measures  Dislocation of settlement with a resulting effect on loss of property, assets and income generation: According to the data on PAPs provided from the Ministry of Industry 102 farming HH of a total population of 440 consisting of 214 males and 225 females are expected to be dislocated. It is also indicated that the case of about 81 farming HH who reside in the area is also being examined for the legality of their entitlements. Furthermore, around 88 married youth population who currently reside in houses built within the premises of the compounds of their parents are also to be affected by loss their houses, as well as farms and grazing lands. The details of PAPs and the loss of property and assets are given in the annex section. However, the Woreda Administration expressed that the above information provided by Bole Sub-city is not complete and will require further refinement. This information is expected to be rectified during the preparation of a Resettlement Action Plan (RAP) is the requirement in the case of the proposed project as per the world Bank′s policy OP/BP 4.12 on Involuntary Resettlement. Other major negative impacts are:  Disruption of social fabric/social relations  Release of contaminants/pollutants from the IZ to the surrounding social and biophysical environment  Impacts on health and safety of people working in the IZ due to inhalation, exposure to hazardous substances, injuries and accidents from machinery, traffic accident, increase in respiratory and eye diseases, HIV and STDs that results in from population agglomeration. FDRE Ministry of Industry Page vi Social and Environmental Impact Assessment Report Mitigation measures for the identified impacts such as the implementation of a Resettlement Action Plan (RAP) with the provision of basic social and economic infrastructures and various pollution and contamination mitigation techniques and measures have been recommended. Environmental and Social Management and Monitoring Plan An ESMP has been prepared taking into consideration all negative impacts, recommending appropriate measures as well as responsible bodies and institutions for mitigation and monitoring. Most of the environmental management work has been found to be the responsibility of the Ministry of Industry and its IZ site management office in relation to the construction and operation of the IZ. Each and every factory will also be responsible for managing its own wastes in terms managing the release and emission of wastes from the factory processes. The contractor and consultant′s site supervisor will also be responsible for the management of adverse impacts during the construction. Monitoring will be conducted by the IZ site office and relevant bodies such as the Ministry of Environment and Forestry, Addis Ababa EPA and Health Bureau. The Woreda office will be responsible for monitoring of the implementation of RAP. The overall cost of Environmental and Social Management is indicated in the table below. No. Description of Unit Quantity Unit Total Remarks Activities Cost Amount (Birr) (Birr) 1 Compensation for the house 93 100,000 930,000 loss of housing 2 Compensation for the ha 750 14,400 10,800,000 loss of agricultural production for a duration of 10 years 3 Skill training for individual 100 3000 300,000 PAPs 4 Restoration of ecology Lump sum 3,000,000 ( physical and biological measures) and establishment of buffer zone 5 Establishment of 2,000,000 buffer zone around the IZ Total 17,030,000. FDRE Ministry of Industry Page vii Social and Environmental Impact Assessment Report Cost for monitoring of the implementation of mitigation measures and control of HIV/Aids and STD is 200,000 Birr/year. In conclusion it can be stated that the implementation of the Bole- Lemi Phase Two Industrial Zone is expected to have significant contribution to the improvement of the economy of the country in general and the local communities in particular. The ESIA that has been conducted shows that the nature of the proposed project and the environmental setting where it is located is such that the key adverse impacts can be controlled and mitigated within acceptable limits. Therefore, considering the long-term socio- economic benefits that can be gained, there are no significant environmental grounds for not proceeding with the proposed implementation of the proposed Bole-Lemi Phase Two Industrial Zone. The benefits that can be achieved from such IZ development far outweigh the negative impacts and inconveniencies. Recommendations have already been given in the relevant sections with respect to minimizing or avoiding some of these negative impacts. The other major point that has to be emphasized is the mitigation measures proposed for loss of assets and income in the form of different compensation measures should be carefully implemented with higher degree of seriousness and accountability. For the proposed project to be successful preparing an appropriate RAP is very important in order to create smooth relationship and get the cooperation of the PAPs which most often is not easy to attain in most development project if their interest is not properly addressed . It is also recommended that the ecology of the IZ should be well maintained and even improved by establishing a carefully conserved and managed green area. Furthermore, implementation of a network of monitoring of ambient quality of air, water, soil, and other environmental resources is very important in order to get data on changes and trends that would give guidance to the discussion makers and stakeholders to take necessary decision to rectify any unforeseen adverse impacts. FDRE Ministry of Industry Page viii Social and Environmental Impact Assessment Report Table of Contents Executive summary ..................................................................................................................................ii Introduction ..............................................................................................................................................ii 1. Introduction and background............................................................................................................... 1 1.1 Introduction ................................................................................................................................... 1 1.2 Project description ......................................................................................................................... 1 1.3 Objective of the Proposed Project ................................................................................................. 2 1.4 Objective of the ESIA Study ......................................................................................................... 3 2 Project description and location ......................................................................................................... 3 2.1 Project location .............................................................................................................................. 3 2.2 Project Description ...................................................................................................................... 3 3 National Policies, Strategies and Regulatory Framework ............................................................... 11 3.1 Policy framework ........................................................................................................................ 11 3.1.1 Constitution of the Federal Democratic Republic of Ethiopia ............................................................ 11 3.1.2 Ethiopia’s Climate Resilient Green Economy Strategy ....................................................................... 12 3.1.3 Environmental Policy of Ethiopia ................................................................................................... 12 3.1.4 Industrial Policy and Strategy of Ethiopia .......................................................................................... 12 3.1.5 Land Tenure Policy ............................................................................................................................. 13 3.1.6 National Policy of Women ................................................................................................................... 13 3.2 Legislative Framework ................................................................................................................ 13 3.2.1 Environmental Impact Assessment (Proclamation No. 299/2002) ...................................................... 13 3.2.2 Environmental Pollution Control (Proclamation No. 300/2002) ........................................................ 15 3.2.3 Proclamation 513/2007, Solid Waste Management ............................................................................ 15 3.2.4 Regulation 159/2008, Prevention of Industrial Pollution ................................................................... 16 3.2.5 Labour Proclamation 377/2003 .......................................................................................................... 16 3.2.6 National Rural Land Administration and Use (Proclamation No. 456/2005) ................................... 16 3.2.7 International Conventions and Protocols ............................................................................................ 17 3.3 Institutional Framework .............................................................................................................. 18 3.3.1 The Environmental Protection Organs................................................................................................ 18 3.3.2 Federal Environmental Protection Authority (EPA) ........................................................................... 18 3.4 Summary of the Relevant World Bank’s safeguard Policies ...................................................... 19 4 Study Methodology ............................................................................................................................ 23 5 Description of the State of Environment ............................................................................................ 29 5.1 Physical environment .................................................................................................................. 29 5.1.1 Climate ................................................................................................................................................ 29 5.1.2 Topography and Drainage .................................................................................................................. 29 5.1.3 Soil type ............................................................................................................................................... 29 5.1.4 Geology and Hydrogeology ................................................................................................................. 31 FDRE Ministry of Industry Page ix Social and Environmental Impact Assessment Report 5.1.5 Land Use /Land Cover ........................................................................................................................ 31 5.1.6 Water Resources .................................................................................................................................. 32 (b) Groundwater well fields ......................................................................................................................... 34 (c) Small scale Irrigation ............................................................................................................................. 34 5.2 Biological Environment .............................................................................................................. 34 5.2.1 Terrestrial vegetation .......................................................................................................................... 34 5.2.2 Wildlife ................................................................................................................................................ 34 5.2.3 Ecologically Sensitive Areas ............................................................................................................... 34 5.3.4 Kotebe Waste Water Treatment plant .................................................................................................. 35 5.3.5 Stone Quarries and Crusher Machines ............................................................................................. 35 5.4 Social and Socio-economic Environment ................................................................................... 35 5.4.1 Population and Settlement ................................................................................................................... 35 5.4.2 Social and Economic Infrastructures .................................................................................................. 36 (a) Education ................................................................................................................................................ 36 (c) Water supply and Sanitation ................................................................................................................... 39 (d) Transport ................................................................................................................................................ 39 (e) Electricity and Telecommunication Services .......................................................................................... 40 5.4.3 Economic Activities ............................................................................................................................. 40 5.4.4 Religious, cultural, historical and archaeological Resources ............................................................. 42 5.4.5 Information and Communication Technology Centre ......................................................................... 42 5.4.6 Environmental and Social Liabilities .............................................................................................. 42 5.4.7 Assumptions and Gaps in Knowledge ................................................................................................. 43 6 Consultations ...................................................................................................................................... 43 6.1 Stakeholder Consultation ...................................................................................................... 43 7 Project Alternatives ............................................................................................................................ 44 8 Environmental Impacts and Proposed Mitigation Measures .............................................................. 46 8.1 Positive Impacts and Enhancement Measures ............................................................................. 46 8.1.1 Income-generation and job creation ................................................................................................... 46 8.1.2 Improved access to basic social services and infrastructures ............................................................. 46 8.1.3 Skill transfer ........................................................................................................................................ 47 8.1.4 Increase in land and asset values ........................................................................................................ 47 8.2 Negative Impacts and Mitigation Measures ................................................................................ 48 8.2.1 Impact on settlement and loss of income generation ........................................................................... 48 8.2.2 Impacts on Health and Safety .......................................................................................................... 49 8.2.3 Impact due the Release of contaminants from Factories ..................................................................... 51 8.2.4 Impact of the industrial zone on the air Aviation Industry .............................................................. 53 8.2.5 Impact of wastes from Recreational centres and residential areas ..................................................... 53 8.2.6 Impact of pollution from fuel stations and garages ............................................................................. 54 8.2.7 Impacts on public infrastructure ......................................................................................................... 54 8.2.8 Impact on land use .............................................................................................................................. 54 8.2.9 Impact of other Project on the proposed Industrial Zone and Proposed mitigation measures ........... 55 8.3 Magnitude of Impacts .................................................................................................................. 56 8.4 Cumulative impact and mitigation measures ............................................................................. 56 8.4.1 Impacts on the Surface and Ground Water Quality ............................................................................ 57 8.4.2 Impacts on Air Quality ........................................................................................................................ 57 8.4.3 Noise Impact ........................................................................................................................................ 58 FDRE Ministry of Industry Page x Social and Environmental Impact Assessment Report 9 Environmental and Social Management Plan (ESMP) ...................................................................... 58 9.1 Institutions Responsible in the Implementation of ESMP........................................................... 58 9.1.1 Ministry of Industry ............................................................................................................................. 58 9.1.2 Ministry of Environment and Forestry ................................................................................................ 59 9.1.3 Addis Ababa Environmental Protection Authority .............................................................................. 59 9.1.4 Industrial Zone Development Corporation, Bole Lemi Industrial Zone Branch Office ...................... 59 9.2 Roles of Institutions in the Implementation ESMP ..................................................................... 60 9.2.1 Construction phase .............................................................................................................................. 60 9.2.2 Operation phase .................................................................................................................................. 60 9.3 Capacity Building Needs for the Implementation of ESMP ....................................................... 60 10 Environment and Social monitoring plan ......................................................................................... 75 11 Cost Estimate for Implementation of Mitigation and Enhancement Measures ................................ 78 11.1 Anticipated resettlement of population and loss of property and assets.................................... 78 11.2 Potential negative health and safety impacts ............................................................................. 78 11.3 Ecological Restoration .............................................................................................................. 79 11.4 Capacity building and training of PAPs .................................................................................... 79 11.5 Costs for Environmental Monitoring ........................................................................................ 79 12 Conclusions and Recommendations ................................................................................................. 79 References ............................................................................................................................................. 81 List of Tables Table 2.1: Type, number and size of the proposed industrial shed Table 2.2: preferred list of the priority industrial sectors of the industrial zone Table 5.1: Type of schools around the project site Table 5.2: Top 1o diseases at Goro Health Center Table 8.1: Type of proffered industrial mix Table 8.2: Predicted pollutant releases from the factories Table 9.1: Social and environmental management plan Table 10.1: Environmental and social monitoring Table 10.2: Cost estimate for mitigation and monitoring List of Figures Fig 2.1: Index map of the project site Fig 2.2: Map of the project area and the surrounding environment FDRE Ministry of Industry Page xi Social and Environmental Impact Assessment Report Fig. 2.3: Satellite imagery of the proposed project site Fig. 5.1: Soil type of the project area Fig. 5.2: Topography contour map of the project area Fig. 5.3: Three dimensional view of the project area Fig. 5.4: Wheat farm at the project site Fig 5.5: Lemi and Tiliku Akaki Rivers at their confluence Fig. 5.6: Pollution level of Lemi River Fig. 5.7: St Teklehymanot Church near the project site Fig. 5.8: Water supply source of ht e community around the site Fig. 5.9: Animal raising and farming at the project site Fig. 6.1: Consultation meeting with stakeholders Fig. 6.2: Consultation meeting with the Project affected population (PAPS) Fig. 8.1: Existing stone crusher plant and the prevailing air pollution List of annexes – In Volume Two Annex 1: List of consulted institutions Annex 2: Checklist for screening and scoping of the project impacts Annex 3: Standards for industrial pollution control Annex 4: Photo album on the project site Annex 5: Minutes of Public Consultation List of abbreviation and acronyms AAEPA Addis Ababa City Government Environmental Protection Authority AIDS Acquired Immune Deficiency Syndrome BOD Biological Oxygen Demand COD Chemical Oxygen Demand EIA Environmental Impact Assessment EIS Environmental Impact Statements EPA Environmental protection Authority EPA Environmental protection Authority EIZDC Ethiopian Industrial Zone Development Corporation FDRE Ministry of Industry Page xii Social and Environmental Impact Assessment Report EMP Environmental Management Plan EMU Environmental Management Unit, ESMF Environmental and Social Management Framework ESMP Environmental and Social Management Plan FDI Foreign Direct Investment FDRE Federal Democratic Republic of Ethiopia HH House Holds HIV Human Immune Virus GHG Green House Gasses GTP Growth and Transformation Program IDA International Development Association IZDP Industrial zone Development Project IZ Industrial zones IZDP Industrial zone Development Project IZDESD Industrial Zone Development and Environmental safeguards Directorate IZDC Industrial Zone Development Corporation MOI Ministry of Industry MEF Ministry of Environment and Forestry MOI Ministry of Industry MSE Micro and Small Scale Enterprises MUDC Ministry of Urban Development and Construction N.A Not Available NGOs Non-Government Organizations OHS Occupational health and safety OP Operational Policies RAP Resettlement Action Plan RPF Resettlement Policy Framework SME Small and Medium Enterprises SME Small and Medium Enterprises FDRE Ministry of Industry Page xiii Social and Environmental Impact Assessment Report PAPs Project Affected Persons ROW Right of Way SS Suspended Solid STD Sexually Transmitted Disease SS Total Suspended Solid TOR Terms of Reference UDP Urban Development Program VOC Volatile Organic Compound FDRE Ministry of Industry Page xiv Social and Environmental Impact Assessment Report 1. Introduction and background 1.1 Introduction Bole Lemi II is one of the five industrial zones planned to be constructed by the Ministry of Industry as part of its programme to promote industries that will produce 60 % for export and 40 % as import substitutes. The Ministry has carried out an Environment and Social Impact Assessment (ESIA) in order to assess impacts of constructing shade facilities, which will be used for various industries in Bole Lemi II site. The ESIA study is prepared to meet the relevant national and World Bank policies, legislations and guidelines. This ESIA report has assessed the state of environment of the project and the project site, predicted significant environmental and social impacts and proposed mitigation that will minimize impacts. It has also recommended some enhancement measures for the positive impacts. Chapters one to three of the ESIA study report presents background information of the proposed industrial zone development project. The baseline data presented the current status of the physical and social environment of Bole Lemi II Site is described in chapter four whereas identification and analysis of potential environmental and social impacts are dealt with in chapter eight. Environmental and social management and monitoring plans are discussed in chapters nine and ten. 1.2 Project description Ethiopia is currently importing more goods than it is exporting and resulted in a trade imbalance between the Country’s import and export of commodities. The Government is therefore committed to balance the trade deficit by establishing industries that are dedicated in the manufacture of export oriented products and products for import substitution. To this effect Government found it necessary to establish industrial zones. Bole Lemi with an area of 186 hectare is one of such industrial zone located on the eastern periphery of Addis Ababa City Administration. This industrial zone is strategically located adjacent to the newly constructed Addis –Nazareth toll road and the new Addis Djibouti rail way that also extends to Djibouti sea Port enabling the factories within the Bole Lemi industrial zone to conveniently export their industrial products out of the country. The land where the industrial zone is sited is agricultural land currently under cultivation by the community to grow crops to support their livelihood. The Government of Ethiopia has given emphasis to ensuring faster and sustained development of the industrial sector in the next five years of Growth and Transformation FDRE Ministry of Industry Page 1 Social and Environmental Impact Assessment Report Plan. Industry zone development in the potentially strategic sites within the country has been found as the best approach to promote the industrial sector. The Government of Ethiopia (GoE) jointly with the International Development Association (IDA) of the World Bank plan to implement Industrial zone Development Project (IZDP) with the financial support of the Government of Ethiopia, the IDA and other donors. The objectives of the proposed industrial zone project is to promote export oriented industrial production and also encourage the production of import substitution to positively contribute to the national economy by attracting investments and improving enterprise competitiveness in the targeted industrial zones (IZ) by carrying out the following four primary components: - Strengthening institutional and regulatory framework for IZ development, and capacity building; - Supporting industrial infrastructure development of IZs; - Enhancing IZ linkages to small and medium enterprises (SMEs) through targeted interventions; and - project management monitoring and evaluation The activities in component two in relation to the Industrial zone development project will involve civil works such as construction and/or rehabilitation of infrastructures and thus it is expected to negatively impact the socio-economic and biophysical environment. These project activities will therefore trigger the World Bank safeguards on Environmental Assessment Policy (OP 4.01) and the impacts will range from small scale to larger scale and is classified as category A according to the World Bank Safeguard policy and Schedule 1 according to the Environment Impact Assessment Proclamation of Ethiopia. 1.3 Objective of the Proposed Project The objective of the Bole Lemi Industrial Zone development Project is to promote industrial development in the country by allocating land and providing in advance the necessary infrastructures to the industrial zone in order to attract national and foreign investors who have the interest to invest their capital and technology in the proposed industrial zone for the manufacturing of industrial products with a target to export 60 % of their products and 40 % for import substitution. FDRE Ministry of Industry Page 2 Social and Environmental Impact Assessment Report 1.4 Objective of the ESIA Study The main objectives of the ESIA study is to assess the potential positive and negative effects, and recommend appropriate mitigating measures that will minimize any undesirable effects expected to result from the construction of an Industrial Zone at Bole Lemi II site. . The study is aimed to ensure that the environmental and social effects of the project activities are adequately and appropriately addressed before decisions are made to implement them. The specific objectives of the ESIA Study of Bole Lemi Industrial zone Development project are:  To ensure that direct and indirect environment and social impacts are identified and properly addressed;  To avoid or minimize the significant adverse impacts of the proposed development projects;  To promote industrial zone development that is environmentally sound and socially acceptable 2 Project description and location 2.1 Project location The second phase Bole Lemi Industrial Zone Development Project (BL-IZDP) is located at the outskirt of the Addis Ababa city about 17 km southeast from the city centre. It is specifically located in Woreda 11(the lowest government administration unit) of the Bole Sub-City under Addis Ababa City Administration. The local name of the project site is Lemi Gossu. It is geographically located between latitudes of 8056’53’’to 8058’17’’and longitudes of 38050’42’’to 38051’35’’ covering an area of 186 hectare. The site is accessible from the City through the main Asphalt road up to Kotebe Waste Water Treatment Plant further down through a small stretch of narrow dry weather road to the site. The Project Site is adjacent to phase one Industry Zone Development Project (IZDP) which is currently nearing completion. 2.2 Project Description The Ministry of Industry together with the Ministry of Urban Development and Construction have developed implementation plan that will help realize the Industry Zone Development Implementation Program in selected towns and cities of the country to enhance the industrial development in the country. The Plan has identified, in addition to other relevant issues, various activities to be accomplished while delineating and demarcating areas of land for establishing industry zones. The Miniseries in their plan have identified four industrial zone project development sites in Addis Ababa, Kombolcha, Dire Dawa, and Hawassa cities. FDRE Ministry of Industry Page 3 Social and Environmental Impact Assessment Report The second phase Bole Lemi Industrial Zone Development Project is one of the industrial zones that have been selected to be developed in Addis Ababa City. The project development in addition to the construction of the industrial sheds will involve the development of various infrastructures such as road, water supply, sewerage drainage and other utilities such as power, telecommunication. Moreover, residential areas, recreation centres such as for example foot ball field and, gymnasium, greenery, car parking, business centres, administration units, storage facilities, garage will be constructed within the industrial zone. The Bole Lemi Industrial Zone Development Project is planned to be implemented in two phases. The first phase which is currently under completion will be implemented on an area of 156 ha of land. The second phase of the Bole Lemi Industrial Development Project whose ESIA study will be conducted under this assignment will rest on 186 ha of productive agricultural land currently in use by the communities around the site. The construction of FDRE Ministry of Industry Page 4 Social and Environmental Impact Assessment Report AddisAbaba City Fig 2.1 Index Map of the Project Site Phase one Bole Lemi Industrial Development Project has been launched since 2012 and about 85% of it has been completed. FDRE Ministry of Industry Page 5 Social and Environmental Impact Assessment Report Industry Zone Phase I Lagoon Farmlands Farmlands Fig 2.2 Location and Description of The Project Site FDRE Ministry of Industry Page 6 Social and Environmental Impact Assessment Report Waste Water Treatment Plant Bole Lemi Industry Zone Phase I Saint Teklehaymanot Church Farmland Lemi River Settlements Big Akaki River Bole River Fig 2.3 Satellite Imagery of the proposed Project site FDRE Ministry of Industry Page 7 Social and Environmental Impact Assessment Report The second phase Bole Lemi Industrial Zone Development project in addition to the construction of the industrial sheds will also be engaged in the construction of on-site and offsite infrastructures and utilities for the supply electricity, water etc. When the proposed project is realized, it is planned to rent this industry sheds for the targeted investors and customers. Two types of factory sheds are proposed to be constructed in the second phase Bole Lemi Industrial Development Project. The first type and second type of industrial sheds including common facilities and parking areas will rest on 5,777m2 and 11,217m2 of land respectively. The Government’s strategy is to build quality factory sheds with common facilities to potential investors and rent them out with fair price. With this intention the Government has the plan to l rent the sheds at the rate of 1USD/m2/Month for the first five years and the rent will increase by some amount thereafter taking into account the prevailing market. The factory shed having an area of 5,777m2 will have 36 meters width and 151,64 meters length and a height of 7 meters and it will have working space of 1008 m 2a for the processing of factory products. Facilities such as showers, hand wash basins and toilets will be provided in this building. The walls of the factory building will be constructed with hollow concrete block for up to 2.2 m height and the rest of the wall height will be completed with Ega sheet. The factory sheds with an areas of 11,217m2 ( width of 72 m, length of 151.64m, height of 7 m) is expected to have working area 2016 m2 for product processing if it is leased for one investor. The factory building of this size will also have showers, hands wash basins and toilets. External walls of the buildings will be plastered and painted with either Quartz or plastic paints and internal walls will be plastered with Oil paint. Toilets walls and kitchen as well as the floor of the canteens will have a ceramic wall cladding and all doors and windows will be made out of aluminium and steel. One transformer will be installed at each factory shed and Distribution boards will be provided at each floor. The type, number and size of buildings that are proposed to be e constructed in the Bole Lemi Industrial Zone development Project are indicated in table 1 below. FDRE Ministry of Industry Page 8 Social and Environmental Impact Assessment Report Table 2.1: Type, number and size of proposed industrial sheds Type of buildings Quantity Unit Area(m2) Total Area(m2) 1 Factory sheds 2 11,217 22434 2 Factory sheds 15 5,777 86655 3 Health centre 1 508 m2 508 m2 4 Bonded warehouses 4 599 m2 2339m2 5 Exhibition centre 1 508 m2 508 m2 6 Shops and Clubs 1 293 m2 293 m2 7 Fire brigade building 1 239m2 239m2 8 Road 7 km - - 9 Common effluent treatment 1 - - Plant. 10 Toilets and Showers 60 30 1800m2 11 Hand Wash basins 102 - - The following types of industries are expected to operate in the second phase Bole Lemi Industrial development Project. Table 2.2: Possible list of light industries in the Second Phase Bole Lemi Industry Zone Development Project No Industrial sector Production 1 Textile industry Textile factories, Cotton and synthetic fibbers, Weaving, pigmenting and dyeing factories 2 Leather Industry Leather dressing factories, Shoe factories 3 Non-metallic industries Plastic industries, Tiles and glue manufacturing, Soap and detergent manufacturing, 4 Metal and Engineering Manufacture and assembly of motor - vehicles, industries Manufacture of other means of transport (trailers, motor-cycles, bicycles), Body -building, boiler - making and manufacture of reservoirs, tanks and other sheet containers, 5 Chemical industries Storage facilities for petrochemical and other FDRE Ministry of Industry Page 9 Social and Environmental Impact Assessment Report chemical products , Production of paints, varnishes, printing industries, processing of petrochemicals and Paint manufacturing 6 Pharmaceutical production of pharmaceutical products 7 Agro-processing industries Manufacture of vegetable and animal oil or Oil processing plants, Manufacture packing, and canning of animals ,fish and vegetable products, Brewing, distilling and malting, Slaughter houses /abattoir, Alcohol and Soft drinks, Flour mill factories, Biscuit factories, Tobacco processing and Other agro-processing industries. According to the information obtained from the officials of the Ministry of Industry, the factories that will be operating in the second phase Bole Lemi Industrial Zone will be light factories that will use finished goods such as textile fabric and finished leather, manufactured in other sites outside of this industrial zone. However, there is a possibility that the type of factories in this industrial zone may end up in an industrial mix different from the above list of factories. This could be due to the fact that investors that will come to invest in this industrial zone may be interested in industries other than the ones listed above. In any case Environmental and Social Impact Assessment has been has been carried out to minimize the impacts for the possible mix of industries before they are established. FDRE Ministry of Industry Page 10 Social and Environmental Impact Assessment Report 3 National Policies, Strategies and Regulatory Framework 3.1 Policy framework The proposed second phase Bole-Lemi Industry zone development Project will be governed by the relevant environmental policies, strategies, proclamations to ensure environmental sustainability. The environmental policies, laws, legislations, proclamations and institutional frameworks pertinent to this project are summarized and presented below. 3.1.1 Constitution of the Federal Democratic Republic of Ethiopia The Constitution is the supreme law of the country, whose provisions are providing guidance to all other policies, regulations and institutional frameworks. The Constitution of the FDRE has various provisions that are aimed to ensure the implementation of development project in an environmentally sustainable manner. The concepts of sustainable development and environmental rights are enshrined in the Constitution of the FDRE through articles 43 and 44, which states among others the right to development and right to live in clean and healthy environment. Article 44(2) of the Constitution states that all persons who have been displaced, or whose livelihood has been adversely affected as a result of state programs have the right to commensurate monetary or alternative means of compensation including relocation with adequate State assistance . The government shall pay fair compensation for property found on the land but the amount of compensation shall not take into account the value of land. Moreover the Constitution states that, without prejudice to the right to private property, the government may expropriate private property for public purposes subject to payment in advance of compensation commensurate to the value of the property (Article 40(8). Moreover, Article 43 (2) dealing with the rights to development states that nationals have the right to participate in national development and, in particular, to be consulted with respect to policies and projects affecting the community. Article 92 of the Constitution states that the design and implementation of any program and development projects shall not damage or destroy the environment, and people have the right to be fully consulted and express their views in planning and implementation of environmental policies and project. FDRE Ministry of Industry Page 11 Social and Environmental Impact Assessment Report 3.1.2 Ethiopia’s Climate Resilient Green Economy Strategy To cope up with the prevailing environmental problems such as land degradation, rainfall fluctuation, increasing temperature, flooding and speed up its socioeconomic development, the Government of Ethiopia has planned a climate-resilient green economy as a development strategy. This development direction promotes environmental protection, reducing fossil fuel consumption which releases greenhouse gases into the atmosphere. With demand for energy growing with the increasing population, industrialization and urbanization, the Government realized that harnessing clean and renewable energy sources such as wind, solar, hydro and geothermal energy sources is critical. 3.1.3 Environmental Policy of Ethiopia The Environmental Policy of Ethiopia (EPE) was issued in April 1997. The overall policy goal is to improve and enhance the health and quality of life of all Ethiopians and promote sustainable social and economic development through sound management and use of natural, human-made and cultural resources and their environment as a whole, so as to meet the needs of the present generation without compromising the ability of future generations to meet their own needs. The policy consists mainly of guiding principles and various sect-oral and cross- sect-oral policies for sustainable environmental management. The policy seeks to ensure the empowerment and participation of the people and their organizations at all levels in environmental management activities, raise public Awareness and promote understanding of the essential linkage between environment and development. In addition to its guiding principles, the policy addresses sect-oral and cross sect-oral environmental issues. 3.1.4 Industrial Policy and Strategy of Ethiopia Ethiopia has set its own industrial policy and strategy as of august 2002.The industry development strategy of the country has put in place the principles that primarily focus on the promotion of agricultural lead industrialization, export lead development, and expansion of labor intensive industries these principles are interdependent and inter linked to one another. The strategy has also set the other principles that clearly stated the pivotal contribution of the private sector, the leadership role of the Government, and the integrated and coordinated participation of the public at large in nurturing the strategy. This strategy refers to those industries which are primarily involved in the production of manufactured gods. Attempt has FDRE Ministry of Industry Page 12 Social and Environmental Impact Assessment Report also been made to include other industrial classified sectors in the document other than the manufacturing industries. 3.1.5 Land Tenure Policy The Constitution of the Federal Democratic Republic of Ethiopia (FDRE) states that the right to ownership of rural and urban land, as well as all natural resources, is exclusively vested in the State and People of Ethiopia. Article 40 of the Constitution indicates that land is a common property of the Nations, Nationalities and the People of Ethiopia, and shall not be subjected to sale or to other means of transfer. The Constitution of FDRE retained land under the control of the people and government of Ethiopia thus, prohibiting its buying and selling. Also article 4(5) of the Proclamation 94/1994 deals with provision of land for the conservation, development and utilization of state forests or protected areas. However, this can be effective only after the consultation and consent of the peasantry and subject to the assurance of their benefits. In general, all legal provisions cited above, make rural lands the property of the People and Government of Ethiopia, and buying and selling of land is prohibited but leasing rights is allowed. Moreover, it is the right for existing land owner to be compensated fully and satisfactorily if land is expropriated by the state. The Land Policy of Ethiopia strongly support that project plans must include attractive and sustainable resettlement strategies to the people who are going to be displaced as a result of the development plan, and they have to be fully convinced, compensated and have to participate in all phases of the project implementation. 3.1.6 National Policy of Women This Policy was issued in March 1993 and stresses that all economic and social programs and Activities should ensure equal access of men and women to the country’s resources and in the decision making process so that they can benefit equally from all activities carried out by the Federal and Regional institutions. 3.2 Legislative Framework 3.2.1 Environmental Impact Assessment (Proclamation No. 299/2002) This Proclamation (No 299/2002) aims primarily at making the EIA mandatory for categories of projects specified under a directive issued by the EPA. The law specifies the projects and FDRE Ministry of Industry Page 13 Social and Environmental Impact Assessment Report activities that will require an environmental impact assessment (EIA). The proponent of the project must prepare the EIA following the format specified in the legislation. The EPA will then review the EIA and either approve the project (with or without conditions) or reject it. The Proclamation requires, among other things:  Specified categories of projects to be subjected to an EIA and receive an authorization from the EPA or the relevant regional environmental agency prior to commencing implementation of the project.  Licensing agencies to ensure that the requisite authorization has been duly received prior to issuing an investment permit, a trade or operating license or a work permit to a business organization.  The EPA or the relevant regional environmental agencies may issue an exemption from carrying out an EIA in projects supposed to have an insignificant environmental impact.  A licensing agency may suspend or cancel a license that has already been issued where the EPA or the relevant regional environmental agency suspends or cancels environmental authorization. To put this Proclamation into effect the EPA issued guideline Documents, which provide details of the EIA process and its requirements. According to this EIA guideline projects are categorized into three schedules: Schedule 1: Projects which may have adverse and significant environmental impacts thus requiring a full Environmental Impact Assessment Schedule 2: Projects whose type, scale or other relevant characteristics have potential to cause some significant environmental impacts but are not likely to warrant a full EIA study Schedule 3: Projects which would have no impact and do not require an EIA However, projects situated in an environmentally sensitive areas such as land prone to erosion; desertification; areas of historic or archaeological interest; important landscape; religiously important area, etc. will fall under category 1 irrespective of the nature of the project. According to this guideline all project proponents and executing bodies (agencies) in the country should operate in close cooperation with the EPA to ensure that proper mitigating FDRE Ministry of Industry Page 14 Social and Environmental Impact Assessment Report measures are designed and implemented, especially for projects with an adverse effect on the environment. This in effect means that an Environmental Impact Statement (EIS) should be prepared by project proponents and be examined, commented and approved by the EPA. 3.2.2 Environmental Pollution Control (Proclamation No. 300/2002) Proclamation No. 300/2002 on Environmental Pollution Control primarily aims to ensure the right of citizens to a healthy environment and to impose obligations to protect the environment of the country. The law addresses the management of hazardous waste, municipal waste, and establishment of environmental quality standards for air, water and soil; and monitoring of pollution. In this connection the Proclamation provides a basis from which the relevant environmental standards applicable to Ethiopia can be developed, while sanctioning violation of these standards as criminally punishable offences Furthermore, it empowers the Federal Environmental Protection Authority or the Regional Environmental Authority to assign environmental inspectors with the duties and responsibilities of controlling environmental pollution. In order to ensure implementation of environmental standards and related requirements, inspectors belonging to the EPA or the relevant regional environmental agency are empowered by the Proclamation to enter, without prior notice or court order, any land or premises at any time, at their discretion. Such wide powers derive from Ethiopia's serious concern and commitment to protecting the environment from pollution. 3.2.3 Proclamation 513/2007, Solid Waste Management Proclamation no. 513/2007 aims to promote community participation in order to prevent adverse effects and enhance benefits resulting from solid waste. It provides for preparation of solid waste management action plans by urban local governments. Therefore, Solid Waste Management Proclamation No. 513/2007 states (Article 5.1) that Urban Administrations shall ensure the participation of the lowest administrative levels and their respective local communities in designing and implementing their respective solid waste management plans. In Article 5.1 each Region or urban administration shall set its own schedule and, based on that, prepare its solid waste management plan and report of implementation. Measures related to waste handling and disposal:  Any person shall collect waste in an especially designated place and in a manner, which does not affect the health of the society. FDRE Ministry of Industry Page 15 Social and Environmental Impact Assessment Report  No person shall dispose solid, liquid or any other waste in a manner which contaminate the environment or affects the health of the society. 3.2.4 Regulation 159/2008, Prevention of Industrial Pollution As a follow up to Proclamation 300/2002, a regulation to prevent industrial pollution was developed by the Federal Environmental Protection Authority and endorsed by the Council of Ministers to ensure compatibility of industrial development with environmental conservation. This Regulation confers important obligations to industrial operators. A factory subject to the regulations is obliged to prevent or minimize the generation and release of pollutants to a level not exceeding the environmental standards. The regulation also obliges industrial operators to handle its equipments, inputs and products in a manner that prevents damage to the environment and to human health. Moreover, the regulations urge industrial operators to prepare and implement an emergency response system of their own. On the other hand industrial operators are required to prepare and implement internal environmental monitoring systems and keep written records of the pollutants generated and the disposal mechanisms used to get rid of the pollutants. In relation to it, factories are required by the regulation to submit annual compliance reports with the provision of the regulations. 3.2.5 Labour Proclamation 377/2003 The Labor Proclamation (which was revised in 2003) provides the basic principles which govern labor conditions taking into account the political, economic and social policies of the Government, and in conformity with the international conventions and treaties to which Ethiopia is a party. The proclamation under its Part Seven, Chapter One, and Article 92 of this proclamation deals with Occupational Safety, Health and Working Environment, Prevention Measures and Obligations of the Employers. Accordingly the Proclamation obliges the employer to take the necessary measure for adequate safeguarding of the workers in terms of their health and safety. Moreover, the Occupation Health and Safety Directive (MOLSA, 2003) provides the limits for occupational exposure to working conditions that have adverse impacts on health and safety. 3.2.6 National Rural Land Administration and Use (Proclamation No. 456/2005) The Rural Land Administration and Use Proclamation (Proclamation No. 456/2005) defines the state ownership of rural land and the tenure rights of the land occupant, including rights to "property produced on his land", rights of inter-generational tenure transfer, and rights of exchange land and limited leasing rights. Provisions are made for the registration and FDRE Ministry of Industry Page 16 Social and Environmental Impact Assessment Report certification of tenure rights. Part Three of the Proclamation presents regulations relating to the use of rural land, particularly as it relates to soil and water conservation and watershed management. The rural land administration and land use laws are to be implemented by the regional states. Land holding right gives the right to use the land for agricultural purposes as well as to lease it and, while the right remains in effect, bequeath it to family members, as well as the right to acquire property thereon, by labor or capital, and to sell, exchange and bequeath the same. The Proclamation also addresses environmental concerns, including non-compliance with directives on environmental protection. Article 7(3) of the Proclamation reinforces the rights of land users to compensation for the development they have made on the land. It also states that when the land holder is evicted by federal government, the rate of compensation would be determined based on the federal land administration law. When the rural land holder is evicted by regional governments, the rate of compensation would be determined based on the rural land administration laws of regions. It is envisaged that the Proclamation will create a sense of ownership among the vast majority of the rural population and enable them to take initiatives and collectively engage in environmental management activities. 3.2.7 International Conventions and Protocols In addition to the national policies, strategies and regulations aimed to protect the environment the government has the obligation to enforce international environmental laws ratified by Ethiopia and are aim to protect the global environment. Among these international environmental protection conventions and protocols the Vienna Convention/Montréal Protocol is the one that has relevance to the proposed project. The Vienna Convention and the Montreal Protocol are the building blocks for the Protection of the Ozone Layer. The measures contained in the Treaties and Amendments are aim to achieve a gradual ban on production and consumption of ozone-depleting substances. Several options were considered for ODS emission control measures. One option considered was to "allocate emission rights on the basis of gross national product and population." The use of some substances is controlled under Montreal Protocol among them are the CFCs (chlorofluorocarbons) and HCFCs (hydro-chloral-flour-carbons) which can be used as refrigerants in refrigeration plants:. Ethiopia became a party to the convention and to the FDRE Ministry of Industry Page 17 Social and Environmental Impact Assessment Report protocol in October 1994. According to article 9(4) of the Constitution of the Federal Democratic Republic of Ethiopia once an international agreement is ratified through the accepted or established procedure, it automatically becomes an integral part of the law of the land. 3.3 Institutional Framework 3.3.1 The Environmental Protection Organs Environmental Protection Proclamation (Proc. 295/2002) is aimed to assign the responsibilities for environmental management to various entities in order to ensure sustainable use of environmental resources, thereby avoiding possible conflicts of interest and duplication of efforts. It is also intended to establish a system that fosters coordinated but differentiated responsibilities among environmental protection offices at a federal and regional level. At the federal level the Environmental Protection Authority is in charge of formulating policies, laws, regulations and standards. Enforcing the laws and policies including EIAs and environmental monitoring, for all projects or activities that falls under the control of the Federal Government also falls within the responsibilities of the EPA. Each of the main federal institutions active in the construction of infrastructure, or economic development is required by law to have its own environmental unit. The Ministry of Water Resource is one of the few federal institutions that indeed have an Environment Unit. According to the Environmental Protection Organs Proclamation, the regional states are required to create their own regional environmental agencies. These institutions are to deal, among others, with EIAs for regionally managed infrastructures or development activities. 3.3.2 Federal Environmental Protection Authority (EPA) The EPA which is now upgraded to the level of ministry is an independent authority, acting outside the main ministerial structures and reporting directly to the prime minister. The federal EPA is the key national level environmental agency, with a mandate to address environmental issues. The environmental legislation gives the EPA powers to fulfill its role, support all federal agencies in establishing environmental units, and develop skills in strategic environmental analysis of policies and public instruments. The EPA is involved in the development of environmental policy and legislation, setting environmental quality standards for air, water and soils, monitoring pollution, establishing EIA procedures and an FDRE Ministry of Industry Page 18 Social and Environmental Impact Assessment Report environmental information system, and undertaking capacity development in relevant agencies to ensure the integration of environmental management in policy development and decision making. 3.4 Summary of the Relevant World Bank’s safeguard Policies OP/BP 4.01 Environmental Assessment The objective of this policy is to ensure that Bank-financed projects are environmentally sound and sustainable, and that decision-making is improved through appropriate analysis of actions and of their likely environmental impacts. This policy is triggered if a project is likely to have potential (adverse) environmental risks and impacts on its area of influence. OP 4.01 covers impacts on the natural environment (air, water and land); human health and safety; physical cultural resources; and Trans-boundary and global environment concerns. The Bank undertakes environmental screening for each proposed projects to determine the appropriate extent and type of EA. It classifies a proposed project into one of the following Categories, depending on the type, location, sensitivity and scale of the project and the nature and magnitude of its potential environmental impacts: Category A: Proposed project is classified as category A if it is likely to have significant adverse environmental impacts that are sensitive, diverse, or unprecedented. Category B: Proposed project is classified as category B if it’s potential adverse environmental impacts on human population or environmentally important areas-including wetlands, forests grasslands and other natural habitats –are less adverse than those of Category A projects. These projects are site specific; few if any of them are irreversible; and in most cases mitigation measures can be designed more readily than for Category A Project. Category C: a proposed Project is classified as category C if it is likely to have minimal or no adverse environmental impacts. Beyond screening, no further EA action is required for a category C Projects. A screening exercise on the present project was conducted by applying the screening format of the World Bank (see Appendix II). Accordingly, it was found that most of the likely significant environmental impacts that will arise from the project implementation are diverse and significant thus the proposed industrial zone development project falls under Category A. FDRE Ministry of Industry Page 19 Social and Environmental Impact Assessment Report This policy under the sub-project will therefore trigger OP/BP 4.01. OP/BP 4.04 Natural Habitat This policy recognizes that the conservation of natural habitats is essential to safeguard their unique biodiversity and to maintain environmental services and products for human society and for long-term sustainable development. The proposed Industrial zone Development Project activities will be implemented in an agricultural land and is not likely to adversely impact any of the Natural Habitats. This project is not therefore going to trigger OP/BP 4.04. OP/BP 4.36 Forests The objective of this policy is to assist borrowers to harness the potential of forests to reduce poverty in a sustainable manner, integrate forests effectively into sustainable economic development and protect the vital local and global environmental services and values of forests. No forest or shrubs of major biodiversity significance will be cleared during the land preparation and construction of the industrial zone development project and other ancillary development activities associated with the provision of infrastructures and various utilities. This policy under the sub-project will not therefore trigger OP/BP 4.36. OP 4.09 Pest Management The objective of this policy is to (I) promote the use of biological or environmental control and reduce reliance on synthetic chemical pesticides; and (ii) strengthen the capacity of the country’s regulatory framework and institutions to promote and support safe, effective and environmentally sound pest management. This policy is not relevant to this project and will not trigger OP 4.09. OP/BP 4.11 Physical Cultural Resources The objective of this policy is to assist countries to avoid or mitigate adverse impacts of development projects on physical cultural resources. For purposes o f this policy, “physical cultural resources” are defined as movable or immovable objects, sites, structures, groups of structures, natural features and landscapes that have archaeological, paleontological, historical, architectural, religious, aesthetic, or other cultural significance. FDRE Ministry of Industry Page 20 Social and Environmental Impact Assessment Report The implementation of this sub- project will not adversely affect the physical cultural resources of the project area. This project will not therefore trigger OP/BP 4.11. OP/BP 4.12 Involuntary Resettlement The objective of this policy is to (i) ensure that the development process fosters full respect for the dignity, human rights, and cultural uniqueness of indigenous peoples; (ii) ensure that adverse effects during the development process are avoided, or if not feasible, ensure that these are minimized, mitigated or compensated; and (iii) ensure that indigenous peoples receive culturally appropriate and gender and inter-generationally inclusive social and economic benefits. The construction of the proposed phase two Industrial Zone Development Project is anticipated to displace more than 200 households. Moreover, the community will loss more than 180 hectares of agricultural land. These and other impacts that will arise during project implementation and operation of the project are anticipated to cause loss of assets and income generation capacities of individuals. The implementation of second phase Bole Lemi Industrial Zone Development Project will therefore obviously trigger OP/BP 4.12. OP/BP 4.37 Safety of Dams The objectives of this policy is for new dams to ensure that experienced and competent professionals design and supervise construction; borrower adopts and implements dam safety measures for the dam and associated works. This policy is not relevant to the proposed project and therefore will not trigger OP/BP 4.37. OP 7.50 Projects in International Waters The objective of this policy is to ensure that Bank-financed projects affecting international waterways would not affect: (i) relations between the Bank and its borrowers and between states (whether members of the Bank or not); and (ii) the efficient utilization and protection of international waterways. This policy is not relevant to the proposed project and therefore will not trigger OP 7.50. FDRE Ministry of Industry Page 21 Social and Environmental Impact Assessment Report OP 7.60 Projects in Disputed Areas The objective of this policy is to ensure that projects in disputed areas are dealt with at the earliest possible stage: (a) so as not to affect relations between the Bank and its member countries; (b) so as not to affect relations between the borrower and neighboring countries; and (c) so as not to prejudice the position of either the Bank or the countries concerned. The project is not located in a disputed area. This policy is not therefore relevant to this project and will not therefore trigger OP 7.60. FDRE Ministry of Industry Page 22 Social and Environmental Impact Assessment Report 4 Study Methodology The Environmental and Social Impact Assessment (ESIA) process incorporates a number of Key steps. The assessment process constitutes a systematic approach to the evaluation of a project in the context of the natural, regulatory and socio-economic environments of the area in which the project is proposed to be implemented. Step 1 screening The consultant has carried out screening based on a screening checklist include in the annex section of this report. According to the guidelines of the EPA and World Banks classification of project in relation to their impacts, the proposed Second phase Bole Lemi industrial zone Development Project falls under schedule 1 which also the same as category A. There are projects which may have adverse and significant environmental impacts a full environmental impact assessment. Step 2 Scoping The second step in the ESIA is to define the proposed project activities and the natural, regulatory (i.e. legal) and socio-economic environments in which these activities will occur. This is achieved through Scoping. Scoping identifies which of the activities has a potential to interact with the environment. Scoping is conducted early in the ESIA process so that a focus on the priority issues (i.e. those that have the greatest potential to affect the natural and/or socio-economic environment) can be established for the rest of the ESIA process. There are a number of key elements to the Scoping exercise as follows:  Gather and review existing environmental and socio-economic data relevant to the proposed development project  Gather and review existing engineering design definition with respect to the proposed water supply and sanitation project. All project elements including construction, installation, commissioning, operations, maintenance and decommissioning will be considered.  Assemble and review relevant legislative requirements, environmental standards and Guidelines associated with the proposed development.  Consult with project stakeholders and other potentially interested and affected parties. FDRE Ministry of Industry Page 23 Social and Environmental Impact Assessment Report Step 3 Detailed data gathering and review Following step 2, engineering, environmental and socio-economic data will be assessed in greater detail to ensure all of the proposed activities and their consequences will be considered in all stages of the development. Step 4 Existing environmental conditions In order to identify any potential impact on and potential change to the natural and socio- economic environments, it is essential to have a thorough understanding of the existing environment prior to commencement of the proposed activities. In this regard there is a need to characterize the existing baseline environmental and socio-economic conditions including establishing the prevailing conditions for a range of media as follows:  Natural environment media such as air, water, soil and groundwater, flora and fauna;  Socio-economic media such as demographics, economic activity and service provisions  Definition of the existing environmental conditions will be achieved by completing two main tasks as follows:  Conducting a detailed review of all secondary data sources (i.e. existing documentation and literature).  Undertaking physical observation to supplement and build upon the existing information base. Step 5 Project alternatives The initial step in defining a project is to identify, at a conceptual level, viable alternatives to the project so that a viable base-case design may be realized. Consideration of project alternatives occurs at two levels as follows:  At the initial stage where we consider the “no development” option  At the design stage where we will explore engineering alternatives within the selected project design definition. Once project alternatives are defined in the Project Concept stages, they are assessed and compared on financial, logistical, technical design, safety and environmental/socio-economic FDRE Ministry of Industry Page 24 Social and Environmental Impact Assessment Report criteria. The project alternative that is determined to likely result in the best balance against these criteria will be typically the one that moves forward into the detailed design phase. The Ministry of Industry request Addis Ababa City Administration to select a viable site for the development of an Industrial Zone. The City Administration selected Bole-Lemi site based on its Master Plan and the local development plan of the area that have already been prepared for the area. According to the City Master Plan this site falls under industrial zone and has ideal location in terms of its proximity to other existing and future industrial sites and major highways and railway line of the city thus making industrial development a viable project alternative. Furthermore, taking its proximity to the capital city of the country and the envisaged land value industrial development is a profitable venture compared to current agricultural activities taking place in the area Step 6 Consultations Project stakeholder consultation is a vital component of the ESIA process. The consultation process focuses on providing information on the proposed Industrial Zone in a manner that can be understood and interpreted by the relevant audience, seeking comment on key issues and concerns, identifying potential impacts and offering the opportunity for alternatives or objections to be raised by the potentially affected parties and other stakeholders. All relevant stakeholders will be identified and consultations at all levels of the ESIA study will be conducted. By conducting such consultations the people that will be affected by or have an interest in the proposed project will have an opportunity to express their opinions and concerns. Step 7 Identification and analysis of the environmental impacts Key, potentially beneficial as well as adverse impacts on the physical, biological and socio- economic environment associated with the construction and operation phases of the project will be identified with the help of checklists, site survey and consultations with stakeholders and affected parties. In addition environmental impact analysis will be carried out in three stages: Identification - This includes description of the existing environment, determination of the project components and definition of the environment that will be modified by the project FDRE Ministry of Industry Page 25 Social and Environmental Impact Assessment Report Prediction - forecasting of the quality and/or spatial dimensions of the changes and estimation of the probability that the impact will occur Evaluation - determination of the incidence or magnitude and significance of the impact before mitigation For this study an effective methodology that will identify an environmentally preferred option and/or clears all development options from environmental perspective is required. The methodology selected is the Rapid Impact Assessment Matrix (RIAM). The RIAM bases its analysis on a standard definition of the assessment criteria to provide accurate and independent score for each condition. The impacts of the project activities are evaluated against the environmental components and for each component a score using the defined criteria is determined. This score then provides a measure of the impacts against the components. The final environmental assessment score is achieved by adding up individual scores for performance, reversibility and Cumulative and multiplying their sum by individual scores for importance and magnitude. This is then compared against the numerical ranges to give a final Range Value (RV) that in turn corresponds to level of significance of changes. A combination of these parameters will be summarized in an all encompassing measures of significance which will be the basis for identifying and prioritizing major impacts and recommending mitigating measures. The predicted environmental and social impacts are characterized as follows: Nature of Impact: Direct, indirect or cumulative; Type of impact: Positive, negative or both Duration of impact: Short term, medium term or long term; Spatial scale of impact: Localized, or widespread Extent of baseline change: Low, medium or high Finally, the magnitude and significance level of the identified impacts will be evaluated as major, high, medium or low significance impacts. Step 8 Environmental Mitigation and Benefit Enhancing Measures Based on the impact assessment feasible and cost effective mitigating and benefit enhancement measures that may reduce potentially significant adverse environmental impacts to acceptable levels will be recommended under this step. FDRE Ministry of Industry Page 26 Social and Environmental Impact Assessment Report Step 9 Environmental Management and Monitoring Plan It will be necessary to monitor and audit project development and operation. Monitoring will provide the information necessary for feedback into the environmental management process and will assist in identifying where additional mitigation effort or where alteration to the adopted management approach may be required. The monitoring plan will describe the various environmental management strategies and generic procedures for their implementation. Further, it will identify the management roles and responsibilities for ensuring that monitoring is undertaken and that the results are analyzed and any necessary amendments are identified and implemented in a timely manner. Step 10 Preparation of ESIA Report The final step is the preparation of the Environmental and Social Impact Assessment Report. This report is expected to address the key issues and impacts affecting overall environmental performance of the project. For this particular project the methodology adopted for conducting the Environmental and Social Impact Assessment study includes the conventional methods which are briefly discussed below.  Field Surveys: The method of field surveying is critical in understanding the likely impacts of a given development project on the particular environment around the project site. An EIA study team has been mobilized for field survey to the project site. The team has made observations in and around the project site to gather essential field data. During site observation information on physical, biological and socio-economic environment has been collected. In addition base line data collection was also done through field investigations.  Interviews with specialists: Project alternatives, designs and processes were discussed with the project engineers with particular emphasis on the reasons establishing the form and scope of the proposed project.  Literature review: Information on existing environmental conditions was obtained from review of various published and unpublished sources. In addition review of studies including the draft ESIA report of phase one Bole Lemi industrial Zone Development Project, the draft resettlement Plan(RAP) of Bole Lemi second phase FDRE Ministry of Industry Page 27 Social and Environmental Impact Assessment Report Industrial Development Project, pre-feasibility study of the Bole Lemi Industrial Zone Project, the World Bank Safeguard Policies, ESMF and the mid- term guidance.  Competent authority guidelines: The Federal and regional legislative and institutional framework, policies, procedures, guidelines etc. has also been reviewed.  Consultation with relevant federal, regional and local authorities: Interviews and discussions with several local authorities and stakeholders have been carried out in the project area. This includes consultation with Ministry of Industry, Bole Sub-City Administration, Woreda 11which is the lowest administration unit.  Community consultation: Community consultation meetings were held to discuss on issues and concerns of stakeholders and project affected parties. The consultation was held in Tekle Haymanot Church with major stakeholders and the project affected population (PEPs). A brief introductory note containing brief description of the project, its positive and negative impacts has been presented by the consultant to stimulate their participation in the discussion. The public participation meeting was held for more than two hour and opinions and comments and concerns from the major stakeholders and the affected people have been forwarded. FDRE Ministry of Industry Page 28 Social and Environmental Impact Assessment Report 5 Description of the State of Environment 5.1 Physical environment 5.1.1 Climate The climate of the Addis Ababa City is characterized by two distinct seasonal weather patterns. The main wet season, locally known as Kiremt, extends from June to September, contributing about 70% of the total annual rainfall. A minor rainy season, locally known as Belg, contributes moisture to the region from mid-February to mid-April. The remaining months are dry season. Based on the data collected and analysed from Bole Airport meteorological station which is close to the industry zone, mean maximum annual temperature over the record periods is 23.50c, and mean minimum annual temperature value is 10.50c. The daily variation in temperature in the area is more pronounced than the annual variation and the calculated mean annual temperature is around 170c. The annual rainfall and wind speed calculated in the area are 1080mm and 0.55km/hr respectively. From field observation and consultation, the wind direction is towards west for most of the seasons. 5.1.2 Topography and Drainage The topography of the Industry Zone is predominantly flat where large part of the proposed industrial zone is found. While the south eastern and south western part of the site is characterized by gentle and rolling topography to the direction of the adjacent rivers. Lemi River flows from North to South bounding the industry zone before it joins Akaki River locally known as Teleku Akaki. Bole and Woji Rivers, a natural boundary of the western side of the industry zone flow into Tileku Akaki River at south west corner of the site. 5.1.3 Soil type From field observation, the site is dominantly covered with black cotton soil. The black cotton soil is deposited over the weathered rock has an average thickness of 0.8m. The black cotton soil in the site is characterized with high plasticity and high degree of swelling. The black cotton soil horizon is thin along southern and western peripheries where rocks are outcropped as a result of erosion due to farming and stone mining activities. FDRE Ministry of Industry Page 29 Social and Environmental Impact Assessment Report Fig 5.1: Soil type of the project area, Vertisol Fig 5. 2 Topography contour map of the project area FDRE Ministry of Industry Page 30 Social and Environmental Impact Assessment Report Fig 5.3: Three dimensional view of the project area 5.1.4 Geology and Hydrogeology The area is located at the Miocene ignimbrite (welded tuff) and trachyte underlain by aphantic basalts and overlain by young olivine porphyritic basalts. It is grey colour and is vertically and horizontally jointed. The project corridor and its surrounding have been subjected to the rift tectonics, which is manifested by a number of major and minor fault systems. The general trend of most of these faults located in northeast and southwest of the site follow NE – SW orientation. From Hydro-geological map of Addis Ababa, fractured and inter granular aquifers of old volcanic rocks in the project site have transmissivity values ranging between mean minimum value of 3m2/day and mean maximum value of about 1700m2/day cover the area. 5.1.5 Land Use /Land Cover The Industrial zone site is predominantly agricultural land dominated by crop production. Cereal crops like Teff, wheat, barley and chickpea are cultivated seasonally. The farmer below is harvesting his crops in the project site. Patches of eucalyptus trees are dominantly scattered around rural residential areas in the southern and western boundary of the Industry zone. There is a sparse settlement within and outside of south eastern and south western boundary of the Industry Zone. The land along the border of the project area slopes towards the river valleys where stone production is very significant. FDRE Ministry of Industry Page 31 Social and Environmental Impact Assessment Report Fig 5.4: Wheat farm at the project site 5.1.6 Water Resources (a) Surface Water Resources The proposed project site is found within River Akaki (locally known as Tiliku Akaki) sub- catchment which traverses Addis Ababa city from north eastern to the southern plains culminating at Lake Aba-Samuel. Akaki River constitutes a number of small streams and rivers. These include Lemi, Bole and Woji Rivers which are all tributaries of Akaki River. The rivers are mostly perennial and their flow direction is from northeast to south east close to the project area. Figure below shows the confluence where Lemi that bounds the eastern part of the proposed IZ joins Akaki River. Fig. 5.5: Lemi and Tilku Akaki Rivers at their confluence FDRE Ministry of Industry Page 32 Social and Environmental Impact Assessment Report From field observation and consultation it can be noted that Lemi River and Bole River are highly polluted from Municipal and industry wastes like MOHA soft drink factory located in the upstream. Extensive stone quarry activities along the embankment of the river is also the source of physical and colour change of the river. According to the information obtained from residents downstream of these rivers, Woji River is heavily polluted from overflow of Waste Water Treatment which they said is also the cause of death of their livestock in the area. The Rivers are prone to various types of pollution due to wastes generated from urban conglomerate of Addis Ababa city and the degree of pollution is very much pronounced during the dry season. During our field visit we also witnessed the untreated waste water dumped from industrial and domestic sources at the upstream reaches the rivers and is seriously polluting the water courses. Fig 5.6 Pollution level of Lei River According to previous study, fractured and inter granular aquifers of young volcanic sequences are the source of groundwater in the area. The yield of drilled wells in these aquifers in most cases is over 10 L/sec. There are 4 wells with depth of 160m-200m adjacent to the Industry Zone drilled to supply total volume of 5184m3/day of water for Addis Ababa City. However, all wells are currently not operational because of electro-mechanical problems encountered in the submersible pumps. Apart from one well with static water level of 15m, the three wells are artesian type of wells for the whole season. The piezometric surface constructed from groundwater point inventory made during previous studies showed that the general groundwater flow direction in the Eastern Addis Ababa where the project site is located is from northeast to southwest direction. FDRE Ministry of Industry Page 33 Social and Environmental Impact Assessment Report (b) Groundwater well fields Currently, South Ayat- North Fanta well field which is one of the five deep Groundwater prospective areas under investigation around Addis Ababa city is within proximity of about 2.5km to the south of the proposed Industrial Zone. But the potential of the well-field has not yet been evaluated. A study has been carried out and results from deep test wells drilled up to 500m depth during the study have shown high prospect of Groundwater potential and the area is believed to be one of the major well fields in the future to supply water to the City of Addis Ababa. (c) Small scale Irrigation Privately owned small irrigation scheme is found near Woori River close to the western boundary of the Industry Zone. The land for the irrigation gets water from the nearby non- operational artesian well under gravity flow. From consultation with the owner of the farmland, the nearby river is polluted and can no more be used for the irrigation. 5.2 Biological Environment 5.2.1 Terrestrial vegetation Project area is virtually devoid of any indigenous trees. However, there are patches of eucalyptus trees and remnants of acacia gradually shrinking in size due to intensive cultivation of cereals such as ‘teff’, barley and wheat by the farmers. 5.2.2 Wildlife Human intervention in the area, consisting of urbanization, intensive agricultural cultivation and encroachment for fuel wood has significantly affected the vegetation cover in the area. Hence, the project site and its surrounding environment couldn’t provide a good habitat to support diverse wildlife species. However, according to the local enquiries, species that are common in many parts of the country like spotted hyenas are seen in the project area. There are no known rare and endangered animal species in the Project Area. 5.2.3 Ecologically Sensitive Areas There is no park or animal sanctuary around the project areas that could be impacted due to FDRE Ministry of Industry Page 34 Social and Environmental Impact Assessment Report the implementation of the proposed industrial zone development project. 5.3.4 Kotebe Waste Water Treatment plant The Kotebe Waste Water Treatment Plant located on the north western boundary of the Industry Zone is currently used to treat liquid waste transported by dump trucks from the eastern part of the city. The sludge treatment consists of 20 self-contained sludge drying beds (15m x 240m each) and 10 lagoons for temporary storage of sludge during the wet season. A number of additional ponds are under construction for further expansion. The method of disposal is by keeping the sludge in the lagoon in wet season and drying it on beds in the dry season. In the dry season, the contents of the lagoon and some of the sludge collected from the city are dried on simple beds designed to evaporate the sludge to a lift able cake by wind and sun action. Among the major problems facing the waste water treatment plant is that chemical wastes from the city are dumped to the site illegally consequently disrupting the biological process in the lagoons. 5.3.5 Stone Quarries and Crusher Machines There are about 13 stone crusher machines within and outside of the Industry Zone. The crusher machines are currently producing fine and coarse aggregates for the city. These different construction materials are obtained from different quarry sites found in and around the Industry Zone. Extensive excavation and crushing of stones are currently causing air pollution due to dust that is generated from the crushing of stones. According to the information obtained from the farmers in the proposed project site the crop yield from the farm land closer to the stone crushing machine is declining from time to time due to the dust. In the future the dust releases from stone crushing machine are expected adversely affect the day to day operation of the factories within the industrial zone. The dust may affect the quality of the products and at the same time the health of the industrial workers. It will be therefore important to relocate the stone crushing machines to a location at least 2 kames away from the proposed industrial zone to minimize the above indicated adverse effects. 5.4 Social and Socio-economic Environment 5.4.1 Population and Settlement FDRE Ministry of Industry Page 35 Social and Environmental Impact Assessment Report According to the data on PAPs provided from Bole Sub-city, 102 farming HH of a total population of 440 consisting of 214 males and 225 females are expected to be dislocated. It is also indicated that the case of about 81 farming HH who reside in the area is also being examined for the legality of their entitlements. Furthermore, around 88 married youth population who currently reside in houses built within the premises of the compounds of their parents are also to be affected by loss their houses, as well as farms and grazing lands. The details of PAPs and the loss of property and assets are given in the annex section. However, the Worda Administration expressed that the above information provided by Bole Sub-city is not complete and will require further refinement. This information is expected to be rectified during the preparation of a Resettlement Action Plan (RAP) is the requirement in the case of the proposed project as per the world Bank′s policy OP/BP 4.12 on Involuntary Resettlement. Other major negative impacts are: With the exception of some isolated houses most of the people are settled in three localities also known as Finchawa (Gurage Sefer), Gossu and Kombolcha. The settlement in its entirety is sometimes called Lemi-Gosu. The inhabitants are mostly followers of the Orthodox Christian Church with very little Muslim population living in the area. Houses made of wood and mud and corrugated iron sheet roofing are very common. Most of them are located at the center of a relatively wider compound. There seems to be some settlement plan since most of the housing is located outside the potential agricultural land in a circular pattern. 5.4.2 Social and Economic Infrastructures Despite its proximity to Addis Ababa, the capital city of the Federal Government, phase two Bole-Lemi Industrial Development Project site is basically located in a rural setting located in an urban fringe. There is no much development going on in the project area with respect to urbanization. Public services and infrastructures are virtually absent. There are no business activities of urban nature and people earn their living by cultivating land. (a) Education There is no any nearby educational facility within the settlements and the area proposed for the establishment of the Industrial Zone (IZ). There is no primary or secondary school around FDRE Ministry of Industry Page 36 Social and Environmental Impact Assessment Report the site Students from the rural settlements of the proposed IDZ are therefore forced to walk for more than one hour to attend in the primary schools located in Sefera and Goro areas of Woreda 11 of Bole sub-city. Most of the nearby schools in the Goro area only cater kindergarten and primary school level education. Students at the proposed industrial zone development project site have to travel far from their residence to even get their Kindergarten and Primary level education which is normally supposed to be closer to settlements. The fact that the schools are far from the settlements has created higher transport expenses to the community making it very difficult for poor families to send their children to school. As per the data obtained from the Woreda 11 Education Office, the educational facilities located at Goro area and Woreda 11 where students from the Bole Lemi area can attend are shown in table below. Table 5.1:Schools around the project site No. Level of education Zone 1 Zone 2 Total 1 Kindergarten 2 6 8 2 Primary Grade 1 to 4 1 1 Grade 1 to 5 1 1 Grade 1 to 8 1 1 Total 4 7 11 The total number of pupil attending in the above indicated Kindergarten and primary schools are about 829 and the number of male and female are 430 and 399 respectively. (b) Health Services The proposed Bole-Lemi IZ is currently served by a Health Extension Program run by Goro Health Center of Bole Sub-city. The Health Center is located in Woreda 11 and is relatively far from the settlements. The health extension program aims at serving Woreda 11 which is the lowest level of Government administration. The focus of this program is basically on prevention rather than treatment. There is no any Health Post or Clinic in any of the three settlements located in the project area which can provide even low level of health services. FDRE Ministry of Industry Page 37 Social and Environmental Impact Assessment Report Any medical treatment is referred to Goro Health Center by the health extension nurse assigned in the area. In the absence of any health post and clinic people have to first travel long distances or else use horse driven cart to reach the health center for any treatment. The ongoing health extension program implements around 16 packages in the area of sanitation, family planning and HIV. However, the program is poorly managed and implemented due to lack of required medical personnel. Nurses assigned to the area most often either appeal for transfer or abandon the job due to the long walking distance required. As such, there is no separate data for the type and nature of prevalent disease types in the area since the diagnosis is made only by the health center which has no specific data for the these specific localities. Discussion with the Woreda 11 Health Office has revealed that Typhus and Typhoid have been reported as the two major diseases in the rural settlements. The Top The ten common diseases of the area that has been provided by the Goro Health Center are given in table below. Table: 5.2: Top Ten Diseases at Goro Health Center No. (Rank) Disease Type 1 Upper Respiratory Tract Infection 2 Acute Fever 3 Urinary Tract Infection 4 Pneumonia 5 Diarrheal Disease 6 Anemia 7 Trauma 8 Mussclo Skeletal Disease 9 Skin & Subcutnis Tissue 10 Others When it comes to the availability of health personnel, Goro Health Center is served by 7 health officers and 7 nurses and 2 clinical nurses. In addition, there are also 2 trained midwifes, 3 midwifery nurses, 3 laboratory professionals, 3 laboratory technicians, 3 pharmacists and 3 druggists. Patients that cannot be treated by the Health Center at Goro are referred to Hospitals in Addis FDRE Ministry of Industry Page 38 Social and Environmental Impact Assessment Report Ababa and their referral is decided depending on the seriousness of the sickness. For medical and surgical they are referred to Yekatit 12 Hospital and for maternity they are referred to Zewditu and Ghandi Memorial Hospitals. These hospitals are about 15 to 20 Kms away the residence of the community at the Bole Lemi Site and it is not possible for the community to get health services from these hospitals in time. (c) Water supply and Sanitation Inhabitants of Bole-Lemi do not have any potable piped water supply system currently. They are not connected to any water supply system. However, there are wells that have been constructed by the Addis Ababa Water Supply Authority (AAWSA) at various locations along the valleys of Weji, Bole and Akaki rivers but not connected to the system yet due to some technical difficulties encountered by the city administration. The communities are currently fetching water from well as can be seen from figure 5.8 below. Fig. 5.8: Water supply source of the community at the project site The communities in the Bole Lemi Industrial Development Project site have shortage of latrines and are mostly defecating in the open air. Even latrines like the ones that are now being constructed in most part of rural areas in the country are virtually inexistent in the project site. Open defecation is rather common (d) Transport Though a standard asphalt road has already been constructed with the objective of creating access to the proposed Bole Lemi IZ, the communities in the Bole Lemi villages are not yet connected to any formal transport system. There are some earthen roads and in some parts gravel roads that crisscross the rural settlements. This were meant to serve the movement of FDRE Ministry of Industry Page 39 Social and Environmental Impact Assessment Report heavy duty trucks that go back and forth to the quarries and crushers located within and without the proposed project area. The only available transport is the horse driven carts that transport people and goods from the area to the market place in Goro. Passengers of this horse driven trucks pay as much as Birr 10.00 (ten) for such a relatively short distance. There is bus service from the city up to Goro. (e) Electricity and Telecommunication Services Currently, the area does not get any electricity. It is not connected to the hydropower grid system of Addis Ababa. The connection stops at the construction site of the Phase One Industrial Zone which is not far from the settlements. The administration had a plan to provide electricity to the communities as part of the ongoing village electrification program. However, the plan seems to have been abandoned when the area was chosen for the establishment of an Industrial Zone probably due to the anticipated dislocation of the communalities in the Bole Lemi area The communities are currently benefiting from the mobile telephone service though the reception is currently very poor. 5.4.3 Economic Activities As indicated earlier, Bole Lemi is largely inhabited by people engaged in rural livelihood. Traditional mixed farming type of agriculture dominated by rain-fed farming is currently the most important economic activity in the three rural settlements (locally known as Menders) that are expected to be affected by the establishment of the IZ. Livestock ownership is comparatively low and is primarily geared towards having some oxen and donkey required for the farming activities and transport. Much of the area is allotted for crop production with very limited grazing land here and there. There is no data on any agricultural production in the Agriculture Office of the Woreda. But the Consultant has crisscrossed the whole area by walking and it has been observed from the standing crops that the area has good agricultural potential. The area is known for its production of cereals like teff, wheat, barley, etc., and beans such as chickpeas and lentils. It is a surplus crop producing area and farmers in this area have never faced any drought which is a common phenomenon in some part of the country. Although not much, there has been some irrigation practice along the Weji River located to the west and drains to Akaki River further south and southwest. FDRE Ministry of Industry Page 40 Social and Environmental Impact Assessment Report Fig 5.9: Animal rearing and farming at the project site Though no data is available in concrete terms, it is reported and has also been observed that some people from the villages especially the young are engaged as daily laborers in many of the construction activities that are going on in and around the Bole Lemi in the nearby Arabssa Condominium site, Goro and Sefera as well as in the nearby Phase I Industrial Zone construction site. Such development activities around the site have provided meaningful economic support to the local community. Working as daily laborer they are currently earning 60 to 80 Birr per day which is about 2 US$ per day. Hence, engagement of these communities in the ongoing construction activities is regarded as another major economic activity next to agriculture. Many of them however are reluctant to be engaged themselves in the construction activities around the site since most of them believe agriculture in the area is sufficient to sustain their life as reported by some of the farmers. For them it was the attitude of considering such jobs as derogatory. Another major economic activity going on in the area is quarrying where stone and gravel producing plants equipped with crashers of different types exist. Basalt rock type that can serve for stone and gravel production seems to be abundant in the area especially along the river valleys of Lemi, Woji, Bole, Kersa that surround the area mainly in southeast, south and south west border of project site which is also predominantly an agricultural land. There are number of quarry and crusher machines in and around the project area. There are around 13 quarry sites in and around the site out of which the six of them are inside the delimited IDZ. In fact local people call the area as “Dingay Werk “meaning to say stone in this area is as valuable and expensive as gold. FDRE Ministry of Industry Page 41 Social and Environmental Impact Assessment Report 5.4.4 Religious, cultural, historical and archaeological Resources Site investigation by the ESIA Consultant and discussions with relevant stakeholders and the inhabitants of the area themselves confirm that there are no recorded historical, cultural and archaeological heritage sites in the area. Similarly, there are no monuments, historical buildings, holy trees/springs or old burial grounds identified within the project area. But there is one church named as St. Teklahaimanot Church located very close but not located within the project area. Fig- 5.10: St. Teklehymanot church near the project site 5.4.5 Information and Communication Technology Centre Currently Information and Communication Technology Centre funded by Bill Gate Foundation is under construction on the western side of the Industry Zone. The consultant was not able to get detailed information on what type of activities Information and Communication Technology Centre will be engaged .It is therefore difficult at this stage to anticipate how the Centre is going too positively or negatively affect the proposed industrial zone and vis versa. 5.4.6 Environmental and Social Liabilities Environmental and social liabilities to the proposed IZ need to be checked in case of any unforeseen consequences that would affect the project in the long run due to some previous activities that took place in the area. According to historical data obtained by way of public consultations there is no any evidence of environmental and social liability related to the site FDRE Ministry of Industry Page 42 Social and Environmental Impact Assessment Report 5.4.7 Assumptions and Gaps in Knowledge Reliability and quality of data to be collected with regard to the proposed project from different sources may involve some degrees of uncertainties due to absence of sufficient information about the environment. Some gap in information and knowledge has been experienced while preparing the ESIA. This basically emanated from the absence of any fully fledged feasibility study of the proposed Industrial Zone on which the ESIA could be based. As such there is no any prior assessment of the biophysical and socioeconomic assessment as well as the feasible mix of factories that would be implemented. 6 Consultations 6.1 Stakeholder Consultation Stakeholders’ consultations have been conducted on environmental and social issues with the Ministry of Industry, Addis Ababa City Administration, Woreda 11 where the project site is located and with the community residing in the project site. Summary of the consultation findings is presented below. Details on the consultation process are given in Annex 1.  All of the consulted community groups were welcoming the IZDP with a caution that it will have all necessary preparation necessary for good environmental performance of the IZDP specifically during the operation phase that would prevent the surrounding community from pollution related health effects.  The meeting also emphasized the need for ownership and commitment of government to ensure the release of the necessary funds to pay off compensations and give the needed support to implementing resettlement action plan with short period.  Another outcome of the consultations was that, the Sub-city should be able to provide basic infrastructures like water, road, electricity and others within the resettlement site for affected People before actual relocation of PAPs takes place.  There is also a major concern on the project and its components particularly in terms of availability and functionality of waste treatment facilities.  Participants raised concern that priorities for project benefits such as job employment and other opportunities may not be given to the affected (local residence)  Unless strong monitoring is forced starting from the design, construction and operation of the project pollution will be a burden to the local communities and the environment. FDRE Ministry of Industry Page 43 Social and Environmental Impact Assessment Report 7 Project Alternatives Similar to other development projects, various sites can be considered for the establishment of the proposed industrial zone .The options can range from considering various sites to the no project option which in effect means the choice of no establishment of industrial zone. All of these options have got their own merits and demerits in terms of economic development and environmental management. In the no project option scenario the economic and environmental situation will remain as it currently exists. In reality this option of course is not an option but is always presented in such an option analysis as the “base” option. The no project option will not change the existing environmental status but the economic development through the establishment of the industrial zone will not be materialized. In this particular case, the site has been delineated as industrial development area in the city master plan and local development plan has been handed over by the Addis Ababa City Administration to the Ministry of Industry for industrial development. The selection of this area as industrial development area is considering the following industrial site selection factors: - Strategic located in the periphery of Addis - Availability of ample land for industrial zone development - In close proximity to the national highway network and Bole International Airport/ New Cargo Terminal - A greenfield development site - Opportunity to design a best practice industrial zone away from residential areas - Opportunity to have a direct/ independent road entrance access for vehicles and trucks - Opportunity to provide proper infrastructure and utilities to the site as per industrial sectors/ demands - Opportunity to phase development according to demand - Immediate access to a variety of types of labor and creation of employment opportunities - International amenities in close proximity (hotels, schools, hospitals, parks etc) FDRE Ministry of Industry Page 44 Social and Environmental Impact Assessment Report The second phase Bole Lemi Industrial Zone is located on the south eastern periphery of Addis Ababa City where the newly constructed Addis Ababa- Nazareth tall road extends to the Djibouti sea port. This site is also close to Bole International Airport, thus making export of its products timely and efficient. The fact that it is located in the Addis Ababa Metropolitan area will also allow it to have access to skilled, semi-skilled and unskilled labor in abundance. The other advantage of second phase Bole Lemi site is that the Government has already installed basic infrastructures such as water supply, electricity, telecommunication and access road to the recently completed first phase Bole Lemi industrial zone. The basic infrastructure already installed for phase one of Bole Lemi will also serve the basic infrastructure needs of second phase Bole Lemi Industrial zone Project. Furthermore, a pre- feasibility site assessment carried out by an independent consultant has identified positive attributes of the Bole Lemi Phase two industrial zone site, confirming that the Bole Lemi phase two site meets the aforementioned selection criteria. In terms of mitigating environmental impacts due to solid and liquid industrial waste, the proximity of Bole Lemi phase two site to the already established Bole Lemi phase one industrial zone would provide the opportunity to efficiently treat the waste in a more economical and environmentally sound manner. FDRE Ministry of Industry Page 45 Social and Environmental Impact Assessment Report 8 Environmental Impacts and Proposed Mitigation Measures 8.1 Positive Impacts and Enhancement Measures 8.1.1 Income-generation and job creation Construction stage One of the most important benefits of the establishment of an industrial zone is the creation of job opportunities for both skilled and semi-skilled and even unskilled sector of the society that reside in and around the proposed industrial area. The benefit even extends to people residing very far from the industrial zone having different types of skills and training that have relevance to the construction activities within the industrial zone. Other sector of the society will also benefit from supplying construction material and other related services. The employment of unskilled and semi-skilled people from the project area is expected to be e significant during the at the construction phase of the project. The construction workers in the project site will in turn create job opportunities for the local community by providing food and drinks to the construction working. To these effect women that reside in the proposed industrial zone site are expected to benefit more by providing the required supplies and services. Operation stage It is expected that local Income-generation and job creation will even be more enhanced due to the greater number of skilled and semiskilled employees that will be engaged at this stage even more permanently. Their number is expected to be in the order of tens of thousands as can be observed from the industrial zones that are already operational like the Eastern Industrial Zone located between the towns of Duke and Bishoftu on the way to Adama. 8.1.2 Improved access to basic social services and infrastructures It is expected that people in and around the project area that used to suffer due to lack of access to basic social and services and infrastructures such as water supply, health, education, electricity and other transport and communication infrastructures will benefit from the services that will be provided by the industrial zone. This is due to the fact that such services will be further enhanced as a result of the demand and requirements that will be created by the industrial zone at both the construction and operation stage. In particular, the PAPs that will FDRE Ministry of Industry Page 46 Social and Environmental Impact Assessment Report be dislocated and resettled in the nearby area but currently lack such services will benefit from the new settlement where these facilities will adequately be provide and these will improve the livelihood of the people in the settlement area. 8.1.3 Skill transfer It has been observed that project area communities in Bole-Lemi are basically farmers engaged in rural livelihood without any diversification of activities. They are therefore expected to benefit through skill transfer if they are encouraged and motivated to be engaged in some of the unskilled and semiskilled activities. 8.1.4 Increase in land and asset values The establishment and functioning of the IZ will of necessity attract more and more people that want to have land for the establishment of businesses and service. There will also be more and more encroachment and agglomeration of people which will ultimately result in the increase in values of land and other assets in the surrounding. Enhancement Measures The positive impacts explained above can only be realized fully and sustainably with the implementation of different facilitation and enhancement activities that are mainly the responsibility of the proponent (Ministry of Industry) and the administrative organs at different levels of Addis Ababa City Administration including the sub city and the . Various trainings and capacity building programs that would allow the PAPs to gain the necessary skill required for engagement in the different job opportunities need to be implemented. It is therefore recommended that the Woreda as well as the Sub-city administrations devise plans and prepare budgets to provide training and create job opportunities and employment to the community in and around the Industrial Zone. Furthermore, PAPs especially women have to be financially supported by the Micro-finance Offices in order to establish businesses that cater different services such as providing food cleaning and gardening within the Industrial Zone. Furthermore, there must be various mechanisms of benefit sharing with the PAPs and communities around by way of establishing some common facilities and services for sports and recreation, establishment of different sport and musical teams that can be fully or partially supported by the IZ for the creation of harmonious relationship and friendly environment. FDRE Ministry of Industry Page 47 Social and Environmental Impact Assessment Report 8.2 Negative Impacts and Mitigation Measures 8.2.1 Impact on settlement and loss of income generation Wellbeing of individuals and communities has to be the central issue in the mitigation of adverse impacts that can arise as a result of the implementation of any development activity. Hence, due consideration of the impact on the settlement and potential loss of income generation of the inhabitants of the proposed industrial zone is very critical issue that will need to be addresses immediately. The proposed Bole-Lei zone will cause the removal of settlements and dislocation of inhabitants residing in the already long time established villages (Menders) of Goss, Finchawa (Garage Sefer), Kombolcha and Melke Koran. The community in these villages is also expected to lose their farmlands and grazing lands. According to the data on PAPs provided from the Bole City Administration 102 farming HH of a total population of 440 consisting of 214 males and 225 females are expected to be dislocated. It is also indicated that about 81 farming HH who reside in the area is also under screening by the composition Committee to ensure legality entitlement of land claimed they are claiming to own. Furthermore, around 88 married youth population who currently reside in houses built within the premises of the compounds of their parents are also going to lose their houses, as well as farms and grazing lands that would result in loss of income generation with huge impact on their livelihoods. Detail information on the asset and land losses of the PAPs are given in the annex section. The information above testifies that displacement and resettlement of residents is significant that need to be addresses immediately and with great care and fairness. Residents displaced by the construction of the project may experience additional impacts such as: • Economic impact resulting from acquiring new housing at a new location; • Impacts on the social fabric. Social and psychological impacts due to the disruption of social relationships and establishing relationships in a new social environment; and • Changes in type and tenure of housing. • Lack of employment in the new settlement areas FDRE Ministry of Industry Page 48 Social and Environmental Impact Assessment Report Mitigation Measures Policy, legal and institutional requirements that deal with expropriation of land by the state for development purposes and the loss of assets and property as well as income generation of project affected populations have been elaborated in the relevant section. Hence, this has to be handled as per the Resettlement Policy Framework (RPF) of the Federal Government of Ethiopia and the World Bank’s Policy of OP 4.12, World Bank Safeguard Policy on Involuntary Resettlement. The loss of farmland and grazing land needs to be compensated by an equal size of land of better or the minimum of a similar production function. In the case of the unavailability of farm land and grazing land in their surroundings other means of compensation can be implemented. It is therefore recommended that an appropriate Resettlement Action Plan (RAP) that takes all loses of livelihood (land, housing, infrastructure, etc.,) is prepared and implemented based on the principle of making the PAPs better off. The recommended mitigation measures can be summarized as follows:  Resettle the project affected persons around the project area and assist them to start their own business and become beneficiary from the project operation as stated earlier in the enhancement of positive impacts.  Prepare a Resettlement Action Plan as per relevant FDRE proclamation and World Bank’s policies  Provide basic public services and infrastructures such as water supply, heath services, schools, electricity, access roads, etc.  Priority should be given to PAPs in the advent of any job opportunities  Implement skill upgrading and training programs for PAPs  Establish Credit and microfinance facilities that benefit PAPSs as per regulations.  Assist the elders and female house heads by creating job opportunity that suit them and take their limitations into account or create jobs for their daughters if they are not capable to handle the job they have been assigned to do. 8.2.2 Impacts on Health and Safety Engineering activities that are performed during the construction stage and the operation of the different industries within the IZ have the potential of impacting human health and safety in general and of those engaged in the industrial production activities in particular. These are accidents and injuries that can affect workers from operating machines, from machines that do not work properly, movement and hauling of goods and equipments as well as traffic FDRE Ministry of Industry Page 49 Social and Environmental Impact Assessment Report accidents. They mostly arise from lack of incorporating appropriate and adequate health and safety as well as protection measures. Other potential impacts to health are respiratory and eye diseases due to exposure to dust and smoke, pigments, etc that create breathing problem and vision impairment respectively. Unsafe water sources and unhygienic conditions bear the risk of additional endemic diseases, such as dysentery, diarrhea and cholera. Possibility of HIV/AIDS and other STDs transmission to workers is also expected to increase during the construction and operation phases of the project. It is also noted that equipment and vehicular movements to and from the industrial zone will increase the possibility of accidents to local communities and their animals in the proximity. Mitigation Measures  Conducting awareness creation and training programs to workers on machine and equipment handling and safety measures.  Awareness creation program for drivers and other machine operators to show maximum restraint and discipline with regards to saving life and property  Awareness creation of safety measures of surrounding communities in collaboration with the administration and traffic police  Provide all necessary protection gadgets, equipment and clothing materials to workers which are prone to hazardous risks and enforce their use  A clause of instructions on safety and protection measures that is normally provided as part of the ESIA should be to design and bid documents during the construction phase.  Put signboards that show necessary protection and safety measures at appropriate locations inside and outside the IZ. Signboards should also be utilized for traffic safety precautions with established speed limits. With regards to potential health impacts implementation of a proper Health Extension Program that works on  Preventive medical care  Availing First Aid Kids  Training and awareness on prevention and treatment of HIV/AIDs and other Sexually transmitted diseases (STDs). FDRE Ministry of Industry Page 50 Social and Environmental Impact Assessment Report  Handling waste and waste disposal Shall be given to workers at both construction and operation phase of the IZ. Implementation of an appropriate waste management program and facilities is very essential. Adequate drainage, sanitation and waste disposal should be provided at workplaces through maintaining appropriate waste disposal systems for solid, liquid and hazardous wastes. This includes the implementation of central landfills, liquid waste disposal systems and incinerators for the IZ as required. Maintaining sanitary conditions in camp sites and work places and provision of sanitation facilities to the workers is also very crucial. 8.2.3 Impact due the Release of contaminants from Factories Sources of potential pollutant release from the IZ and the expected type of pollutants have already been examined in the table above. These are basically metal and engineering, chemicals, pharmaceuticals and agro-processing industries. The specific pollutants from the metal factory may include scrape metals, metal dust, fly ashes, metal chips, noise from machines and heavy metals such as chrome, silver, copper, zinc ,lead from the electroplating section, scrape plastic from the plastic factory, bulk of left over cloths and leather cuts from the textile and leather garment factory, effluent loaded with detergent from the detergent factory, various chemicals consisting of hydrocarbons in the effluent of the chemical factory and effluent loaded with organic wastes such as blood, hair and fats and un wanted animal parts (animal carcass) from abattoirs (slaughter house) and meat processing and packing. Water is a very vital environmental resource which plays a very critical role in life support functions. As has been indicated in the discussion on baseline environment, the Bole-Lemi area is very important for its surface and groundwater resources. There is a great potential risk of contamination of both resources due to contaminants and pollutants that emanate from the different activities of the IZ at both construction and operation Stages. However pollution during the operation stage is the most significant. Rivers like Beshale, Lemi, Weji/Bole/Kersa cross the project area and finally drain to Akaki River, which is a very important contributor of water to the Awash River Basin, which of course is the most economically significant river in the country so far. Due to the already existing huge agglomeration of pollutant industries in the Akaki, Aba Samuel, Modjo, river systems further contamination can be catastrophic to the surrounding human life as well as the flora and fauna unless all necessary precautionary measures are taken. Though a slow and FDRE Ministry of Industry Page 51 Social and Environmental Impact Assessment Report gradual process, it is very difficult to reverse any potential deep pollution of groundwater resources. It has been observed during the field visit that the contamination and pollution of the rivers that bound the proposed IZ is already alarming. The release of pollutants and contaminants such as chemical releases and other hazardous wastes from the IZ will also adversely affect the soils, fauna and flora within and without the IZ. The same is also with the potential emissions of dust, smoke, etc., from the IZ that affect ambient air quality. There is also a potential for noise and vibration impacts that results in from the operation of different machineries and vehicles conveyors, etc., in the IZ. Mitigation Measures The first and most important mitigation step should be the creation of industrial subzones depending on pollution risks and compatibility of activities. The factories that will be established in the phase two Bole Lemi Industrial Zone will need to be clustered based on their process compatibility for avoiding cross contamination from the anticipated pollutant crossing boundaries of the individual factories. Accordingly, the 186 hectares of land allocated for the Bole Lemi Industrial Zone is proposed to be divided into the following five sub zones: Subzone one: textile and leather garment Subzone two: metal and plastic processing Subzone three: chemical and chemical processing Subzone four: Agro processing Subzone five: pharmaceuticals Furthermore, factories will need to have pretreatment units to treat their specific wastes by installing precipitators and filters to reduce the release of greenhouse gases into the atmosphere and construct chimney to disperse flue gases high in the air. Factories may also use the option of recycling and material reuse and also employ cleaner production options by optimizing their resource use and conserving their energy use. Factories will also need to put in place pretreatment facilities to remove specific pollutants that are generated from processes prior to releasing their waste into the common treatment facility. FDRE Ministry of Industry Page 52 Social and Environmental Impact Assessment Report The waste waters from each factory after pretreatment will need to be further treated in a common treatment facility to treat the waste water to the level of satisfying the limits indicated in the industrial effluent standards set by the Ministry of Environment and Forestry before releasing it into the nearby river or streams. The pollution type and load coming out of the factories could be specific related to the specific process or it could be of general nature common to all processes. The type of waste common all industries will include waste water from the cleaning of floors and gas emissions such as carbon dioxide, nitrous oxide, sulfur dioxide from boilers and high stacks. 8.2.4 Impact of the industrial zone on the air Aviation Industry Phase two Bole Lemi Industrial Zone is located very close to the run way of the Bole International Air Port where frequent takeoff and landing of international flight takes place. The establishment of abattoirs in Bole Lemi industrial zone is expected to generate animal Caracas and these will attract birds to the site. This may cause bird hazard to the aviation industry and may cause plane accident. The industrial zone is also expected to be impacted from the noise pollution during takeoff and landing of aircrafts. Mitigation Measures To prevent air plane accident from bird hazard animal carcass should be removed and transported away from the industrial zone site and the airport zone .Moreover, regular monitoring on the bird population and movement should be made. To minimize the impact noise pollution on the industrial zone due to landing and takeoff of aircraft sound proof materials should be used as much as possible when constructing the industrial sheds 8.2.5 Impact of wastes from Recreational centres and residential areas Numbers of residential blocks are expected to be built within the industrial zone for the industrial workers. Moreover, there will be recreational centers such as hotels, gymnasium, coffee houses and tea rooms. Solid and liquid waste is expected to be generated from the house and recreational centers and if these wastes are not properly managed will pollute the nearby soil, stream and rivers. Mitigation measures To properly manage the solid and liquid wastes from the residence and recreational centers it will be essential to put in place Proper solid waste collection and disposal system and also provide a appropriate sewerage and drainage networks to properly convey the wastewater into FDRE Ministry of Industry Page 53 Social and Environmental Impact Assessment Report the common waste water treatment facility and an appropriate solid waste disposal facilities outside of the industrial zone. 8.2.6 Impact of pollution from fuel stations and garages The industrial zone is expected to have its own fuel stations and garage for the maintenance of its vehicles. If the garage and the fuel station is not properly managed the soil around the garage and the fuel will be contaminated with fuel and lubricants. Proposed Mitigation measures The underground fuel tank should be properly installed to avoid fuel leakage to the ground water and should also be equipped with fire alarm and appropriate sign posts to prevent the fire accident in the fuel station. To this effect the industrial zone will need to have its own fire brigade with firefighting fleets of vehicles for it to swiftly act upon during the occurrence of fire accident in any part of the industrial zone. As regards to contaminants that are emanating from the garage, contingency plans for the containment of leakage and spillage will need to be prepared to prevent soil pollution around the garage area. 8.2.7 Impacts on public infrastructure Currently, there is no adequate infrastructure such as water supply, health, road, electricity, in the proposed industrial development site. The immediate demand of the IZ for such infrastructures can create shortages and stresses on the existing facilities given the limitation in the currently prevailing constraints of services and the resulting need for huge capital demand in availing these services. Mitigation Measures The project has to allocate additional budget to ease the shortage and stress on the existing infrastructure. 8.2.8 Impact on land use As indicated earlier, the proposed Bole-Lemi IZ is currently having an agrarian land use type allotted much for crop and animal farming and agrarian housings with almost nothing of public infrastructure development. Much of it is occupied by farmland and grazing land. There is also an appreciable area around homesteads that is occupied by eucalyptus trees. Other trees are mostly patchy and are around the river valleys. Hence, it is anticipated that the establishment of the IZ will bring a total transformation of the existing land use. Much of the FDRE Ministry of Industry Page 54 Social and Environmental Impact Assessment Report greenery will be lost to accommodate the numerous sheds, housing, tarmac roads and other infrastructural requirements of the IZ causing some loss of aesthetic. 8.2.9 Impact of other Project on the proposed Industrial Zone and Proposed mitigation measures Basically, the impacts described below can be treated as the impacts of the surrounding environment on the project rather than the impact of the project on the surrounding environment. They are indicated here for reasons that they have to be mitigated for the smooth running and operation of the industrial zone. (a) Impact of the existing lagoon on the Proposed Industrial Zone and the Environment The domestic and industrial waste water from the Addis Ababa eastern catchment is disposed of into the lagoon very close and to the western side of phase two Bole Lemi Industrial zone project site. It is anticipated that bad smell from the lagoon will reach the industrial zone due to the prevailing adversely affecting the residents and workers of the industrial zone. Such a nuisance is not compatible to this type of industrial setting. Mitigation measures To minimize such nuisance smell it is therefore very important to delineate buffer zone around the IZ and introduce smell/odor reducing measures such as dense plantations of trees that can serve as wind barriers, improve aesthetic and also improve aroma that would ameliorate the offensive smell. (b) Impact of quarry sites and Stone Crushers one and the Surrounding Environment There are numerous quarry sites and crushers in and around the Zither stone crashing plants are currently blowing dust on the proposed Industrial zone site. The Consultant has observed that dust generated from such stone crushing plants has virtually covered crops, grasses, and even the roofs of houses located near the proposed industrial zone site .This challenge will remain to be nuisance to the proposed IZ . The same holds true to noise pollution. FDRE Ministry of Industry Page 55 Social and Environmental Impact Assessment Report Fig 8.1: Stone crusher plant and Air pollution Mitigation Measures The proposed Industrial zone and the stone crushing plants around it are not compatible activities that should operate in parallel. It is therefore important that these stone crushing plants d be relocated elsewhere if the industrial zone in a healthy environment. 8.3 Magnitude of Impacts Magnitude of Impacts both positive and negative impacts of the proposed Industrial zone Development project have been assessed in the previous chapter. However, it will be worthwhile to show the magnitude of the already identified impacts in terms of weighing the scale of the benefits that can be gained by the positive impacts and severity of the negative impacts ones. The magnitude of each of the identified impacts is indicated on the annex section 8.4 Cumulative impact and mitigation measures Industrial Zone projects in combination with other government or private sector activities could have larger and more significant cumulative impacts. At this stage, however, the information available to assess cumulative impacts of the IZ and other related projects appropriately is minimal. It is envisaged that a more detailed cumulative impact assessment will be prepared when more information is gathered on the kind of industries to be established and impacts of other similar projects during the feasibility study. The following cumulative impacts and mitigation measures were prepared on the basis of the limited information available. FDRE Ministry of Industry Page 56 Social and Environmental Impact Assessment Report 8.4.1 Impacts on the Surface and Ground Water Quality Bole Lemi River Water Quality that drains the catchment of the proposed second phase industrial Zone and the ground water quality around the proposed site are expected to have deteriorated due to the release of wastewater from the lagoon currently handling domestic wastewater collected from the Eastern Catchment of Addis Ababa City. When the two industrial zones are made operational, Bole Lemi River and the ground water around the site are expected to receive additional industrial wastewater load especially when the common treatment facilities of the industrial zones are not properly functioning. The release of waste water form Bole Lemi First Phase and Second Phase Industrial Zones is expected to bring about cumulative impacts on the already deteriorating river water and ground water quality. Mitigation measures To minimize the cumulative impacts of the waste water from the treatment plant of the second phase Bole Lemi Industrial Zone on the Bole Lemi river water and ground water quality, it is recommended to properly treat effluents from the Industries. Regular samples of waste water should be taken from the inlet and the outlet of the common treatment facility for analysis to ascertain that the treatment plant of the proposed industrial zone is properly functioning and rectify in case of failure to treat the industrial waste water to the required effluent standard set by the Ministry of Environment and Forestry. 8.4.2 Impacts on Air Quality The six stone crushing plants currently operating around the proposed site have already degraded the air quality around the proposed industrial site. When the stone crushing plants are operating simultaneously, visibility at some places is reduced to about 50 meters. If the release of pollutants from the industrial processes of the second Bole Lemi Industrial Zone is not controlled to meet the standards set by the Ministry of Environment and Forestry, it will have cumulative impact on the air quality already degraded from the stone crushing plants operating around the site. Mitigation Measures The activities of the stone crushing plants are not compatible with the activities that are going to be carried out in the proposed industrial zone and to mitigate the cumulative impact on the FDRE Ministry of Industry Page 57 Social and Environmental Impact Assessment Report air quality, it is recommended that these crushing plants be relocated to a site where such an effect will not be felt by the industrial zone. 8.4.3 Noise Impact It is expected that the factories during the process will generate some noise. Since the airport is very close to the proposed industrial site, the noise from the airplanes during landing and take-off will have cumulative noise impact especially on the workers in the industrial zone. Mitigation Measures To minimize the cumulative noise impacts, it is recommended that the factory partition walls and the roofing to be constructed with sound proof materials. 9 Environmental and Social Management Plan (ESMP) 9.1 Institutions Responsible in the Implementation of ESMP The environmental and social management plan indicates major impacts, the proposed mitigation measures, monitoring requirement and also identifies the organizations assigned to implement such plan. The mitigation measures that are likely to arise from implementing the proposed project are explained in the previous chapters and here attempt will be made to correlate the impacts, mitigation measures, monitoring and the budget requirements with the institutions responsible for implementation. The Ministry industry, the EPA of the Addis Ababa City Administration, the contractors and the factory owners will take the responsibility of implementing the proposed environmental and social management plan. The following section describes the organizational responsibilities for the implementations of the environmental management plan of the phase two Bole Lemi Industrial Zone Development Project. 9.1.1 Ministry of Industry The Ministry of Industry will be responsible for the supervising and monitoring compliance with environmental safeguards frameworks) and reporting on a quarterly basis to relevant authorities and IDA. The MOI will assign specific responsibility to the Industrial Zone Development Corporation (IZDC).It is proposed for the IZDC to hire an Environmental and Social Specialist that will supervise the overall implementation of the environmental management plan. FDRE Ministry of Industry Page 58 Social and Environmental Impact Assessment Report 9.1.2 Ministry of Environment and Forestry The Ministry of Environment and Forestry (MEF) has the primary responsibility for ensuring that all investment projects comply with national EIA regulations and the requirements. Following the screening, review and comment of environmental impact statements it approve project EIAs and issue an environmental permit/ license where applicable. The Ministry of Environment and Forestry MEF also undertake environmental audits where required to ensure that projects are complying with their Environmental Management Plans (EMPs) and their commitments to environmental management, mitigation and monitoring. However, the Ministry of Environment and Forestry has delegated its authority to the Ministry of Industry to ensure the enforcement and implementation of the EIA laws in the industry sector and to undertake EIA review and approval works. 9.1.3 Addis Ababa Environmental Protection Authority The Addis-Ababa city Government has adopted the Federal Proclamation on Environmental Impact Assessment. The city Government version of the proclamation is titled ‘Environmental Impact Assessment Regulation of Addis-Ababa city Government No. 21/22006’. Addis Ababa Environmental Protection Authority (AAEPA) has the responsibility to review, comment and approve EIAs of all projects to be established within the city government boundary. Project proponents are required to present approval certificate from the AAEPA or its branch offices by preparing and submitting EIA. Exceptions to this are projects with trans- boundary impact and those projects licensed by the Federal Government. During the operation period, the environmental indicators listed in the previous chapter will be monitored by the EPA of the Addis Ababa City Administration. In general the EPA of the Addis Ababa City Administration is expected to supervise all activities related environmental monitoring during the operation phase 9.1.4 Industrial Zone Development Corporation, Bole Lemi Industrial Zone Branch Office The IZDC and its branch offices at IZ project site among other things will be responsible for managing the industrial Zone development Project in an environmentally sustainable manner. The Office has the responsibility of supervising and monitoring proper implementation of the mitigation measures indicated in the ESMP during construction and operation phases of the project. FDRE Ministry of Industry Page 59 Social and Environmental Impact Assessment Report 9.2 Roles of Institutions in the Implementation ESMP 9.2.1 Construction phase During the construction phase the contractor will be responsible for implementing the proposed environmental mitigation measures in the ESIA report. The contractor will implement the propose mitigation measures and the environmentalist assigned by EPA will monitor the proper implementation of the mitigation measures as per the plan. The contractor has full responsibility for ensuring that all works will be carried out as per the environmental requirement specified in the ESIA study. It is also envisaged that environmentalist with broad range of knowledge and experience in environmental management system of the industrial sector be assigned intermittently to supervise proper implementation of the mitigation measures. Moreover, the environmentalist conjunction with the Ministry of industry has the responsibility of the overall coordination of the environmental management activities during construction. The environmentalist is also expected to guide and advise the construction supervisor and the local authorities as regards to the implementation of the mitigation measures and the monitoring of impacts. 9.2.2 Operation phase During the operation period, the environmental parameters indicated in the previous chapter and also shown below will be monitored jointly by the EPA of the Addis Ababa City Administration and the Ministry of Industry. In be more specific the EPA of the Addis Ababa City Administration is expected to all activities related environmental monitoring during the operation phase 9.3 Capacity Building Needs for the Implementation of ESMP The implementation of SEMP and number of environmental management measures of Industrial Zone Development Project (IZDP) are dependent on the capacity of the implementing agencies in environmental management. In order to ensure this, a program of capacity building for MoI, IZDC, IZDP, AAEPA , sub – project proponents, , Consultants and contractors and the other stakeholders will be put in place to ensure that, the capacity to carry out environment management activities for industrial Zone Development projects. From the consultation that has been made with stakeholders it has been realised that the institutions responsible for the implementation of the proposed mitigation measures have limited capacity to implement the proposed ESMP. However these institutions have FDRE Ministry of Industry Page 60 Social and Environmental Impact Assessment Report regulatory and institutional framework to assure IZ project compliance with the national and international environment policies It is therefore required to build the capacity of the above indicated institutions to enhance their environmental management skills by providing training in the following areas:  screening impacts, scoping assessments, planning mitigation options, public consultation to assess feasibility and acceptability options;  project design to minimize environmental impacts and social disruption; restoration of drainage patterns, land use etc; including mitigation measures in contracts; management of impacts during construction and operation and monitoring of the effectiveness of implementation;  Monitoring environmental performance, reporting, supervision use of various formats during implementation and operation phase, documentation, complaint response, record keeping and other procedures; To this effect comprehensive training plan will be designed with the aim to enhance capacity of relevant stakeholder and meet the following objectives.  identify, prepare, implement & manage environmental aspects of sub-projects;  ensure that the agencies have the capacity to assist in preparing sub-project proposals, mitigation plans; and  Ensure that the implementing agencies have the capacity to appraise, approve and supervise the implementation of subprojects; and training plans. The above indicated training programs are proposed to be provided to the institutions responsible for the implementation of ESMP to meet the above indicated objectives.  familiarization with GOE Environmental management policies and WB safeguard policies;  procedures and methodology in the preparation and implementation of EIA;  review of environmental assessment reports;  Conducting Public Consultation;  Implementation of monitoring program;  Establishment of environment database; FDRE Ministry of Industry Page 61 Social and Environmental Impact Assessment Report  Evaluation of environmental impacts; These training activities and capacity building program will be developed and implemented by professional agencies with adequate experience in imparting such training programs. The resources for implementing the program will be allocated from the respective component of IZDP and will be co-ordinate by the Environment Management Department of the Industrial Zone Development Corporation The table below shows the social and Environmental management Plan (ESMP) of Bole Lemi second Phase Industrial development Project. FDRE Ministry of Industry Page 62 Social and Environmental Impact Assessment Report Table 9.1: Social and Environmental Management Plan (SEMP) of the proposed project Major Impacts Recommended Mitigation Measures Institutions Institutions responsible Time Horizon responsible for the for monitoring the Implementation of Implementation of mitigation measures mitigation measures Impact on the Socio-economic Environment Loss of assets and income -bring into effect appropriate compensate Ministry of -Addis Ababa Before project generation due to land for lost assets and income as per rules and industry/Industry Zone Environmental Protection construction phase acquisition and displacement regulations of the country and the WB Development and Authority(AAEPA) Protection Directorate /Ministry of Environment and Forestry(MEF) Occupational health and safety Maintain walking and working surfaces Factory owners and Addis Ababa City During operation of the factory workers clean and dry and provide workers with managers Administration/Health phase anti-slip footwear; Bureau Provide workers with training in the proper use of equipment (including the proper use of machine safety devices) and personal protective equipment (PPE), such as hearing protection; Ensure that the process layout reduces opportunities for process activities to cross paths, thus avoiding collisions and falls; Demarcate transport corridors and working areas and ensure the proper placement of handrails on platforms, ladders, and stairs; Ground all electrical equipment and installations in wet rooms. FDRE Ministry of Industry Page 63 Social and Environmental Impact Assessment Report provide proper ventilation of enclosed or semi-enclosed areas to reduce or eliminate exposure to dust and aerosols; Install exhaust ventilation equipped with filters and / or cyclones, at sources of dust; Ensure physical segregation of work and welfare facilities to maintain worker personal hygiene; Train employees in chemical handling (e.g. the correct interpretation of material safety data sheets, international chemical safety cards, and first aid procedures). Seasonal and other temporary workers should be fully trained before they work with chemicals; Apply preventive maintenance (e.g. regular inspections) to reduce the risk of burns from all pipes carrying steam and all hot surfaces; When feasible, use hot water, rather than solvents, to facilitate cleaning. Storage of incompatible materials (acids, bases, flammables, oxidizers, reactive chemicals) in separate areas, and with containment facilities separating material storage areas Use of flame arresting devices on vents from flammable storage containers Prohibition of all sources of ignition from FDRE Ministry of Industry Page 64 Social and Environmental Impact Assessment Report areas near flammable storage tanks Health effect from noise and - Ensure vehicles and earth moving - Project contractor -Construction Supervisor During construction dust releases during machines have their mufflers intact construction of the factory -consultant buildings due to land levelling - Limit earth moving machineries from and other earthmoving and working in late night hours. heavy duty machinery operations Moisten soil by sprinkling water during construction Use of water in the industrial - Drill own boreholes or use some of the consultant Ministry of During design, zone during construction and boreholes in and around the project area industry/Industry zone construction and operation may exacerbate the that have not been connected to the system Development and operation already prevailing shortage of to supplement the potential water shortage Environment Protection water supply around IZ. problem. Industry Zone Directorate Development and Protection Directorate Addis Ababa Water Supply Authority Nuisance resulting from dust - Moistening the soil by sprinkling water Contractor Construction supervisor During Construction and noise due to construction as required. activities - Use of appropriate machineries. - Avoid night time work FDRE Ministry of Industry Page 65 Social and Environmental Impact Assessment Report Impact on the Biophysical environment - Establish a formal system within IZ that During operation consists of collection, transport recycling phase Improper management of solid (i.e. composting) and safe disposal of solid Factory owners and Addis Ababa EPA & liquid waste in the new waste and other contaminants. managers industrial zone is expected to pollute and contaminate water, - Establish waste screening system that soil and the surrounding segregates hazardous waste from other -Ministry of biological environment in and wastes. industry/Industry zone around the industrial zone Development and including nearby rivers and - Develop a complete internal sewerage Environment Protection downstream. network with a centralized on-site Directorate wastewater treatment. - Implement plan to regularly transport hazardous waste to a properly designed sanitary landfill - Plan and procure additional dump and vacuum trucks -Strengthen and integrate the waste collector organised under SMEs with the formal SWMS. Install waste bins of different colours at each industrial shed, along the passage ways for collecting and segregating organic & inorganic solid wastes separately. - Integrate the industrial zone waste FDRE Ministry of Industry Page 66 Social and Environmental Impact Assessment Report management system with the primary waste collection scheme of the city run by the SMEs. - Introduce the practices of waste sorting and salvage reusable & recyclables within the factory. - Dispose the remaining solid waste at the sanitary landfill. Air pollution from the factories -Introduce appropriate emission reducing Factory owners and -Addis Ababa EPA During Operation and utilities which include: measures such as: managers Phase Exhaust gas emissions (carbon -cleaner production options in the dioxide [CO2], nitrogen oxides manufacturing process. -Ministry of [NOX], Sox, PM, VOCs and industry/Industry Zone carbon monoxide [CO]) result -Use of common boiler for industries Development and from the combustion of gas and Environment Protection fossil fuel oil or diesel in Directorate turbines, boilers, compressors - Install exhaust ventilation equipped with and other engines for power and retention systems such as cyclones, heat generation. scrubbers, electrostatic precipitators or bag Emissions of particulate filters matter/dust (of various materials) during processing/handling activities Enclose production activities that cause (in exhaust, fugitive, and odor and operate under vacuum; with a leakages) caustic, alkaline, or ozone scrubber system or incinerate the gas in a boiler plant. Odor emissions from various processes, on-site wastewater treatment, substitute less volatile substances, such as Volatile Organic Carbon (VOC) aqueous solvents; emissions are caused by the use FDRE Ministry of Industry Page 67 Social and Environmental Impact Assessment Report of solvents, lubricants Fumes of metallic oxides, -Collect vapors through air extractors and acid/alkali vapors subsequent treatment of gas stream by removing VOCs with control devices such as condensers or activated carbon absorption; -Collection of vapors through air extractors and subsequent treatment with destructive control devices -Use fume suppressants as additives to electroplating baths to reduce air emissions of electroplated metals Generation of waste, including Minimizing hazardous waste generation by Factory owners and -Addis Ababa EPA During operation hazardous waste from factory implementing stringent waste segregation managers Phase of the project process to prevent the commingling of non- hazardous and hazardous waste to be managed. -Ministry of industry/Industry Zone Investigation of external markets for waste Development and recycling by other industrial processing Environment Protection operations located in the neighborhood or Directorate region of the facility (e.g., waste exchange) Use uncontaminated sludge from on-site wastewater treatment for agricultural fertilizer or production of biogas. Store waste in closed containers away from direct sunlight, wind and rain Substituting raw materials or inputs with FDRE Ministry of Industry Page 68 Social and Environmental Impact Assessment Report less hazardous or toxic materials, or with those where processing generates lower waste volumes Applying manufacturing process that convert materials efficiently, providing higher product output yields, including modification of design of the production process, operating conditions, and process controls. Introduce good housekeeping and operating practices, including inventory control to reduce the amount of waste resulting from materials that are out-of- date, off-specification, contaminated, damaged, or excess to plant needs Introduce procurement measures that recognize opportunities to return usable materials such as containers and which prevents the over ordering of materials Avoid product, and by-product losses (e.g. from spills, leaks, excessive changeovers, and shut downs) through the adoption of good manufacturing procedures and facility maintenance; Where possible and subject to sanitary requirements, segregate solid process waste and non-conforming products for reprocessing into commercial products and byproducts Optimize product filling and packaging equipment to avoid product- and FDRE Ministry of Industry Page 69 Social and Environmental Impact Assessment Report packaging-material waste; optimize the design of packaging material to reduce the volume of waste Use spent bleaching earth as a feedstock for brick, block, and cement manufacturing; Use as fertilizer, if not contaminated with heavy metals; Dispose of by anaerobic digestion and then use it for land spreading; If contaminated, manage accordingly Separating metal dust or scrap by type to promote recovery and recycling; Generation of wastewater -Plan and implement the segregation of Factory owners and -Bole Lemi Industrial Zone During project from cleaning and factory liquid effluents principally along managers Branch Office operation phase processes industrial, utility, sanitary, and storm water categories, in order to limit the volume of Organic content, BOD, COD, water requiring specialized treatment. Nitrogen, phosphorus Salinity, Acids, alkalis, -Identify opportunities to prevent or reduce wastewater pollution through such Detergents, Emulsifiers, measures as recycle/reuse within their surfactants, disinfectants facility, input substitution, or process Microbial load modification (e.g. change of technology or operating conditions/modes). Suspended and dissolved solids -Introduce mechanism for water use Metal oxides and salts efficiency to reduce the amount of wastewater generation Phenol, grease, oil and fat -Designing and Construction of common FDRE Ministry of Industry Page 70 Social and Environmental Impact Assessment Report Residues of solvents, pesticides wastewater treatment plant that would accommodate the combined waste characteristics of all industries and utilities. -Process modification, including waste minimization, and reducing the use of hazardous materials to reduce the load of pollutants requiring treatment. - Avoid product, and by-product losses (e.g. from spills, leaks, excessive changeovers, and shut downs) through the adoption of good manufacturing procedures and facility maintenance; -Separate and collect product waste, including rinse waters and by-products, to facilitate recycling or further processing for subsequent use, sale, or disposal -Install grids to reduce or avoid the introduction of solid materials into the wastewater drainage system; -Separate process and foul drains in process areas ; -Adopt best-practice methods for facility cleaning, which may involve manual or automated Cleansing approved chemicals and / or detergents with minimal environmental impact and compatibility with subsequent wastewater treatment FDRE Ministry of Industry Page 71 Social and Environmental Impact Assessment Report processes. -Select disinfection chemicals to match the cleaning operation being applied on the process equipment to the type of problem; Apply cleaning chemicals using the correct dose and application; -Properly treat and discharge cleaning solutions (e.g. through a soap-splitting process) to separate oil and fatty acids from the water phase and then through a fat trap; -Neutralize wastewater that contains metals and phenols which is s typically highly alkaline or acidic before being discharged. -Wastewaters with recoverable metals should be separated from other wastewater streams and metals should be recovered from solution (e.g. using electrolytic cells or hydroxide precipitation); Soil erosion and degradation Appropriate backfilling of trenches Ministry of industry/ Addis Ababa During and after due to construction work Industry zone Environmental Protection construction Planting grasses to cover deep cuts Development and Authority(AAEPA) Protection Directorate /Ministry of Environment Rehabilitate any quarries or damaged land and Forestry(MEF) surface Construction Supervisor FDRE Ministry of Industry Page 72 Social and Environmental Impact Assessment Report Depletion of resources use Intervention to minimize impact energy -Factory owners and - Bole Lemi Industrial Zone (water and energy use) and energy use include: managers Branch Office Increase the efficiency of water and energy use through improving the production processes, raw material use , awareness of the employees and stakeholder involvement; Insulating steam pipes / tubes; Eliminating steam leakage and using thermostatically controlled steam and water blending valves return condensate to the boiler house for re-use Minimize the number of boilers or heaters used to meet loads. Typically more efficient to run one boiler at 90% of capacity than two at 45%. Minimize the number of boilers kept at hot–standby use economizers to recover heat from flue gases to pre-heat boiler feed water or combustion air Introduce measures for adequate water collection, spill control and leakage control system (introduce flow control optimization system) stressed on the existing water Implement appropriate waste management Addis Ababa Water Ministry of industry/ During operation supply, sewerage and drainage system (Increase water treatment and supply and Sewerage Industry zone Development systems due to increase in disposal facilities) Authority and Protection Directorate population and additional FDRE Ministry of Industry Page 73 Social and Environmental Impact Assessment Report demand from industries FDRE Ministry of Industry Page 74 Social and Environmental Impact Assessment Report 10 Environment and Social monitoring plan For this particular project monitoring will be applied on the following general parameters.  Hazardous Wastes  Ambient Water Quality  Ambient Air quality  Ecology  Socio-economic issues  Public complaints In addition to the above indicated parameters it is also recommended that samples of waste water from the outlet of the common treatment facility should be taken for analysis and the results of the analysis be sent to the Ministry of Environment. The inspectors from the Ministry should also do random sampling to confirm the treatment facility is properly functioning and that effluent that are released into the environment meets the required standard .The factories in the industrial zone should also prepare audit plan that will enable them to gradually meet the set targets and submit the audit report to the Ministry at least every six months for their follow up. Monitoring of these parameters is essential to ensure that impacts are fully evaluated and that necessary mitigation measures are applied. For this particular the following environmental and social monitoring indicators, frequency of measurement and reporting requirements are indicated in table 11.1 Table 10.1: environmental and social monitoring requirements S. No Impacts Monitoring Frequency of Frequency Budget per Indicators measurement of reporting year in Birr A Construction phase 1 Soil erosion and dust generation Rate of erosion, Once a Ones a year 2,000 due to ground leveling , sedimentation, year excavation of industry shed formation of gullies foundation and construction of and dust generation access roads, drainage sewerage and other facilities 2 Number of cases of HIV Aids and Number of cases Every Every six 5,000 FDRE Ministry of Industry Page 75 Social and Environmental Impact Assessment Report other sexually transmitted disease month months Operation phase 3 Impact on the project affected Livelihood Twice a Every year 5,000 population restoration year for the first three years Aesthetic value Degree of change Once in the - 2,000 in land use first year 3 Impact of noise, dust and gaseous, Level of noise, Once every Every year 10,000 solid and liquid waste releases dust, solid, liquid month for from the factories into the and gaseous waste two years premises of the industrial zone releases at selected and the surrounding sites within and environment outside of the industrial zone 4 Bad smell from the existing -Frequency of N.A Every year - lagoon and the proposed abettors complain from bad within the IZ smell -The parameters and the permissible limits that will be monitored for the proposed industrial sectors at specific locations are indicated in the annexed industrial effluent standard prepared by the Ministry of environment 5 pollution of the nearby rivers and Measurement of Twice a Every year 10,000 chemical and FDRE Ministry of Industry Page 76 Social and Environmental Impact Assessment Report boreholes biological year parameters 6 Impact on the general state of -establish Once a year Every year 10,000 environment monitoring network and sampling station -Analyze samples to determined air, soil and water quality at sampling station 7 General health condition of the Number of Once Every year 10,000 community patience in the every year health institutions 8 Occurrence of fire risk at the No of fire accidents Every day Every six 2,000 factories and the industrial zone in one month months 9 Health and safety of the factory No of accident in Every day Every six 5,000 working environment the factory per months month 10 Efficiency of the pretreatment Specific parameters Every day Every 50,000 plan common treatment facility such as for the month pretreatment plant general parameters such --- for the common parameters. Cost of monitoring per year 111,000 Note: - Monitoring reports from the factories should be sent to the EPA of the Addis Ababa city administration for compilation and follow up - The EPA of the Addis Ababa City administration will assign environmental inspector to monitor waste releases from the factories into the surrounding environment FDRE Ministry of Industry Page 77 Social and Environmental Impact Assessment Report - Monitoring cost will be covered by the institution responsible to undertake the monitoring 11 Cost Estimate for Implementation of Mitigation and Enhancement Measures As per the Environmental Guidelines of EPA, the ESMP should contain preliminary cost estimates to ensure that mitigation measures and monitoring are adequately funded. At this stage it is expected that the cost estimate can only be indicative. The ESMP and cost estimate are also expected to be revised once construction and operational activities are well defined. As far as the ESMP requirement of the implementation of the proposed Phase Two Bole-Lemi Industrial zone is concerned the following cost components were taken into consideration. 11.1 Anticipated resettlement of population and loss of property and assets As indicated, the displacement/relocation and loss of income on the part of the PAPs requires restoration and improvement of their livelihood by implementing appropriate compensation measures through a fully-fledged RAP. However preliminary cost estimate for compensation in this respect was made as per the Ethiopian Government Resettlement Policy Framework and World Bank’s Policy which consider the potential loss of agricultural production and loss of income generation that comes as a result over duration of 10 years. Hence as per the data provided by the Bole Sub-city the loss agricultural land of the more than 100 HH is estimated to be around 75ha. An estimate of the productivity of the agricultural land was made based on the production per ha of Teff (the most important crop in the area). With the consultation of key informants from among the PAPs and the Agriculture Office of Woreda 11, production of Teff which also takes the value of crop residue into account was taken as 12qt per year. The average price per quintal of the last five years was taken as Birr 1200.00 per qt. This was multiplied by 10years as shown in the summary table of cost estimates. This estimate came to be Birr 10,800,000.00 Cost for housing lost for the 93 houses at an average of birr 100,000.00 per each house is also included as Birr 930,000.00. 11.2 Potential negative health and safety impacts Much of the mitigation problem related to health and safety of the employees of the IZ that arise as a result of construction and operation of the IZ is expected to be answered by the implementation of appropriate design for work related health and safety and inclusion of inbuilt safety equipments and gadgets in the design and construction. Engineering physical features such as traffic signs, speed control measures, pedestrian crossing structures etc. are FDRE Ministry of Industry Page 78 Social and Environmental Impact Assessment Report also taken as design and construction cost.This shall be specified and quantified in the engineering design and included in the BOQ. Again, the cost of the health and safety mitigation measures during the project operation should be concern of the owner of the factory. However, a lump sum cost of Birr 90,000.00 for the implementation of some health extension program that focus on prevention that can be implemented through awareness creation and distribution of some items for the reduction of transmission of HIV/AIDS and other STD has been included. 11.3 Ecological Restoration As indicated in the discussion of negative impacts, some physical and biological damages to the natural environment and aesthetic of the area within the IZ and the surroundings is also anticipated entailing cost of Ecological Restoration by way of implementing required physical and biological measures such as top-soiling, tree planting, grassing that would make improvements. Rehabilitation of quarry and crusher sites as well as buffering of the IZ is also required and a lump sum budget of Birr 3,000,000.00 is indicated for the above purposes. 11.4 Capacity building and training of PAPs Last but not least, the implementation of some programs that work for tailored capacity building and trainings of the PAPs that would create favorable ground either for the employment of the PAPs in jobs required by the IZ or create their own businesses that can benefit from the establishment of the IZ is also very important. A lump sum budget of Birr 300,000.00 has been allocated for the training of 100 individuals at the cost of Birr 3000.00 for each for this purpose. 11.5 Costs for Environmental Monitoring Allotment of budget for the monitoring of appropriate implementation of the recommended mitigation measures with respect to maintaining required environmental quality is very important. The monitoring activities including costs have been put in a separate table. 12 Conclusions and Recommendations The implementation of the Bole- Lemi Phase Two Industrial Zone is expected to have significant contribution to the improvement of the economy of the country in general and the local communities in particular. Though it is a Schedule 1 or Category A project, with anticipated adverse impacts, the ESIA that has been conducted shows that the nature of the proposed project and the environmental setting where it is located are such that the key adverse impacts can be controlled and mitigated within acceptable limits. The main negative impacts are the dislocation of population and loss of property and assets, project waste generation including hazardous chemicals. Most of the adverse impacts will be of a temporary nature, and can be managed to acceptable levels with good engineering design, construction methods, implementation of appropriate environmental mitigation and management measures and monitoring of their proper implementation and effectiveness. FDRE Ministry of Industry Page 79 Social and Environmental Impact Assessment Report Therefore, considering the long-term socio-economic benefits that can be gained, there are no significant environmental grounds for not proceeding with the proposed implementation of the proposed Phase Two Bole-Lemi Industrial Zone. The benefits that can be achieved from such IZ development far outweigh the negative impacts and inconveniencies. Recommendations have already been given in the relevant sections with respect to minimizing or avoiding some of these negative impacts. The most important ones are:  The mitigation measures proposed for loss of assets and income in the form of different compensation measures should be carefully implemented with higher degree of seriousness and accountability.  For the proposed project to be successful preparing an appropriate RAP is very important in order to create smooth relationship and get the cooperation of the PAPs which most often is not easy to attain in most development project if their interest is not properly addressed .  It is also recommended that the ecology of the IZ should be well maintained and even improved by establishing a carefully conserved and managed green area and delineating buffer zone around the industrial zone.  Implementation of a network of monitoring of ambient quality of air, water, soil, and other environmental resources is very important in order to get data on changes and trends that would give guidance to the decision makers and stakeholders to take necessary decision to rectify any unforeseen adverse impacts.  Different capacity and training programs shall be envisaged to improve the lots of the PAPs by engagement in productive and profitable works that would enable them to restore their livelihoods and make them better-off. FDRE Ministry of Industry Page 80 Social and Environmental Impact Assessment Report References African Development Bank group’s policy on environment, 2004 Addis Ababa Atlas of Demography and Socioeconomic indicators, By Finance and Economic Development Bureau Population Affairs Coordination Sub process, April, 2010 Annandale, D. (2001) Developing and evaluating environmental impact assessment systems for developing countries, Impact Assessment and Project Appraisal, 19: 187-193 SA (2007), Central Statistical Authority the 2007 Population and Housing Census of Ethiopia; Environmental Impact Assessment Guideline, Addis Ababa, EPA /MEDAC (April 1996), Environmental Protection Authority in collaboration with Ministry of Economic Development and Cooperation: The Conservation Strategy of Ethiopia; Vol I-V . EPA: Environmental Impact Assessment Procedural Guideline 2003, Addis Ababa. Environmental and Social Management Framework Urban Local Government Development Project, Ministry of Works and Urban Development, November 2008 ERA (2002), Ethiopians Roads Authority: Resettlement/Rehabilitation Policy Framework, Addis Ababa. FDRE (1995), Federal Democratic Republic of Ethiopia.: Proclamation for the Establishment of the Environmental Protection Authority. Proclamation No. 09/1995. Addis Ababa. FDRE (2002), Federal Democratic Republic of Ethiopia: Environmental Impact Assessment Proclamation. Proclamation No 299/2002. Addis Ababa. FDRE (2000), Federal Democratic Republic of Ethiopia: Environmental Pollution Control Proclamation. Proclamation No 300/2002, Addis Ababa Proclamation on the Establishment of Environmental Protection Organ. Proclamation No 295/2002, Addis Ababa FDRE (April 1997), Federal Democratic Republic of Ethiopia: Environmental Policy of Ethiopia, Addis Ababa FDRE (1995), Constitution of the Federal Democratic Republic of Ethiopia Proclamation No.1/1995, Addis Ababa Ministry of Agriculture, Land Use Planning and Regulatory Department: Geomorphology and Soils Map of Ethiopia. Addis Ababa MOA (1993), Ministry of Agriculture, Ethiopian Forestry Action Program: Draft Final Report, Volume 2- The challenge for Development, Addis Ababa MOA (1999), Ministry of Agriculture, Natural Resources Management and Regulatory Department, Agro-ecological Zones of Ethiopia, Addis Ababa. FDRE Ministry of Industry Page 81 Social and Environmental Impact Assessment Report UNIDO, Industry and Development, Global Report, United Nations Publications, Birmingham, 1990/1991 World Bank (1995), The World Bank Roads and the Environment: A Hand Book. www.epa.gov.et (Official Web site of Ethiopian Environmental Protection Authority FDRE Ministry of Industry Page 82 Annexes Annex 1: List of consulted institutions ...................................................................................... 2 Annex 2: Checklist for screening & scoping of project impacts................................................ 8 Annex 3: Standards for Industrial Pollution Control ............................................................... 12 Annex 4: Photos Album of the project site .............................................................................. 21 Annex 5 Minutes of public consultation .................................................................................. 29 Annex 1: List of consulted institutions Stakeholders’ consultations have been conducted on environmental and social issues with the Ministry of Industry, Addis Ababa City Administration, Woreda 11 where the project site is located and with the community residing in the project site. Accordingly, consultations were made with the Deputy General Director of Industrial Zones Development Corporation, Director of Industrial Zone Development and Environmental Protection Directorate, Industrial Zone Development Team Coordinator and with the senior Expert in charge of Bole-Lemi Industrial Zone Development of the Ministry of Industry. Federal Ministry of Industry At the Federal Ministry of Industry level discussions and consultations were made with the following officials and senior experts.  Ato Yargal Mesker, Deputy Director, Industrial Development Zones Corporation,  Ato Telahun, Team Coordinator of the Industry Zone Development section,  Ato Nebiyeleuel, Director of the Industry Zone Development and Environmental Protection Directorate,  Ato Milkias Teklegiorgis, Coordinator of the World Bank Project,  Ato Gebremicheal and Ato Tensai senior experts responsible for the Bole Lemi and Kilinto Industrial Development Projects and Moreover, meeting was conducted with the experts from the World Bank and the Ministry on the 30th of November 2013. The participants in this meeting were Dr. Asferachew, environment specialist of the World Bank Country Office, Dr Chudi , senior sociologist of the World Bank, Mr. Sanjay Srivastava, lead environmental specialist of the World Bank from Washington DC and Ato Milkias, World Bank Project Coordinator of the Ministry of Industry. The objective of the meeting was to see how the ESIA study is progressing and the challenges that may be faced by the consultant to meet the deadline of submitting the ESIA report by December 15, 2013 which has been set by the World Bank. In the meeting the TOR provided to the consultant was discussed in detail and the information gaps that may occur when conducting the ESIA Study in the absence of feasibility study report of the proposed industrial zone. In the meeting the experts of the World Bank advised the consultant to fill the information gap by reviewing the ESIA report of the phase one Bole Lemi Industrial Zone Development Project, the ESMF prepared for Bole Lemi and Kilinto Industrial Zone development Project, RAP Report prepared for Bole Lemi Industrial zone. The experts from the World Bank also noticed the information gap on the type of factories that will be sited in the proposed industrial zone and the difficulty in anticipating impacts from the industrial processes. From the briefing made by the representative of the Ministry and the participants of the meeting there is a general understanding that the industrial sectors will include in general textile and leather garment factories, foot wears factories, pharmaceuticals factories, fertilizers, chemicals and metal and metal products with a target of exporting 60 % of their products and 40 % of their products for import substitution. The participants of the meeting advised the consultant to consider the industrial sector in its broader sense as indicated above and prediction of potential positive and negative impacts and identify the type of pollutants that may be released from these factories into the environment. In the meeting it was also revealed that the proposed set of industrial sector are those that do not release heavy pollutants to the surrounding environment and do not include activities such as textile dyeing and leather tanning categorized as major pollutants of the environment. Bole Sub-city At the level of Bole Sub-city discussion was made with Ato Engeda, official responsible for Land development and City Rehabilitation at the Sub City Administration Level. During the discussion Ato Engeda explained how Addis Ababa Administration selected Bole Lemi Site for the proposed industrial zone development project. In selecting the site Addis Ababa City Administration has taken into consideration the Master Plan and Business Development plan of the City. Woreda 11 At the level of the Woreda discussions and consultations has been made with Captain Hailu Lobe, currently serving as a Manager of Woreda 11 and continued at different levels with within the Woreda Administration. Consultation with stakeholders A meeting was organized at Bole Woreda 11 administration office on December 6/2013. Six executive committee members, who represent the different offices such as the offices for Public Relations, Justice, Health, Housing and Construction, Capacity Building, etc., have attended the meeting. The meeting was chaired by the Manager himself who gave the introduction about the overall development and in particular about the establishment of the industrial zones. The consultant presented to the participants of the meeting briefly about the nature and type of the proposed industrial zone, potential positive and negative impacts as well as possible ways of enhancing the positive and abating or mitigating the negative ones. He also expounded about the roles and responsibilities the and its line offices can play in the overall study particularly in the management and monitoring activities using the Environmental and Social Management Plan (ESMP) that will be prepared by the environmental consultant. This was done in order to obtain their views and concerns as regards to the anticipated impacts of the proposed industrial zone project and the way the consultant proposed to handle these impacts. Consultation meeting with affected population and their representatives The participants from their past experience expressed their reservations and said their concerns are most often by passed in the planning and implementation of similar projects previously implemented in their area and sometimes they are not given appropriate responses to the issues they raise in relation to settlement and compensation In conclusion, they affirmed that they will do whatever they can to support the proposed industrial zone development project. Similar consultations have been conducted with the office of Agriculture, Health, Education, Small Scale and Micro-enterprises of the Woreda. In this meeting all meeting participants raised the issues s related to dislocation and resettlement of Project affected Populations (PAPs) and the challenges that may be faced in the process of their implementation. The discussion made with the members of the Offices for Micro Finance and Micro and Small Scale Enterprises Promotion was particularly very important in relation to dislocation and resettlement. This meeting gave the consultant an opportunity to assess the capacity to provide assistance during rehabilitation and livelihood restoration of the PAPs and also explore its capacity to provide training and area of job creation and employment generation. Consultations with Project Affected People A meeting of representatives of the PAPs was conducted on December 8/2003 at Bole-Lemi village locally known as Gossu Mender. This was attended by a representative of the Administration and about 30 PAPs. The representative explained about the ESIA and the objectives of the meeting and gave the floor to the ESIA Consultant. The ESIA Consultant gave a brief presentation on the following issues:  Definition of Industrial Zone  The nature and type of the proposed Industrial Zone  Potential Positive Biophysical and Socioeconomic Impacts  Possibility of enhancing the positive and mitigation of the negative impacts  The role the communities can play in such a process in the implementation o the proposed industrial zone. The Consultant concluded his presentation he invited PAPs to forward their views and opinions on his presentation. In response the requests made by the consultant the project affected people express the following onions; • In their view they are comfortable with the farming business however they also agree with the implementation of the hope that Government would give due attention to the affected people by adequately compensating for the assets and the agricultural land they will loss and also resettling them by providing the necessary infrastructures that would provide water, electricity, health services and education to their children. They also stressed the need for the Government to give due attention to the restoration of their livelihood and further improvements by way of availing job opportunity in the proposed industrial zone. Minutes of the consultation meetings is included in the annex section List of consulted Individuals and Institutions No. Name of contacted Title Institution telephone Person 1 Ato Milkias TekleGiorgis Coordinator, World Bank Project Ministry of Office Coordinator industry 2 Dr Asferachew Abate Environmental specialist World Bank Country Office 3 Dr Chudi Okafor Sociologist World Bank, Washington DC 4 Mr. Sanjay Srivastava Lead Environmental Specialist World Bank, Washington DC 5 Mr NebyeLeul Fantahun Director, Industry Zone Development Ministry of and Environmental Protection Industry Directorate 6 Mr Yaregal Misker Deputy Director, Industrial Ministry of O911217509 Development Zones Corporation Industry 7 Mr Tilahun Gemechis Team Coordinator, Industry Zone Ministry of Development Industry 8 Mr. Mengistu Regassa Advisor, State Minster Ministry of Industry 9 Mr GebreMichael Senior expert, Bole Lemi Industrial Ministry of 0913231792 Gebrekidan Zone Development Project Industry 10 Mr Mahari Wondemagn Director,Environment Monitoring Ministry of Directorate Environment and Forestry 10 Mr Tinsaea Yimam Senior expert, Kilinto Industrial Zone Ministry of 0911746304 Development Project Industry 11 Mr. Engeda Core process leader, Land Bole City development and City Rehabilitation Administration 12 Captain Hailu General manager, Woreda 11 091142014 13 Ato Kebede Gemeda Member, Compensation committee O0911899326 representing the PAPs Annex 2: Checklist for screening & scoping of project impacts Item Description of key Environmental Magnitude of the Impacts Mitigation Remark No. impacts Measures Significant Minor None Yes No 1 Biophysical Environment o Mobile equipment exhaust X X o Construction dust X X o Road exhaust X X o Car Exhaust X X o Chemicals like benzene, lead, X X chlorine, etc. 2 Water pollution o Turbidity/ Color/ siltation/ X X sedimentation o Garbage X X o Oil & Fuel X X o Tar X X o Trash X X o Run-off pollution X X 3 Soil Pollution Significant Minor None Yes No o Disturbance in soil strata/structure X X due to construction o Chemicals like fuel, oil & grease X X o Plastics X X 4 Soil Erosion/ Landslide and Subsidence o Surface erosion X X o Internal erosion X X o Rupture X X o Landslides X X o Subsidence X X 5 Hydrological Impacts o Interruption of streams & rivers X o Creation of headed borrow pits X that affect ground water level o Excavation, construction or X reclamation of wetlands (marshes, lagoons & mangrove) o Reduction in infiltration & X X replenishment of ground water 6 Impact on Ecosystems and Significant Minor None Yes No Vulnerable Fauna & Flora o Taking-out of natural space X X o Severance (creation of a barrier or X X isolation) o Accessibility (to damage of fauna X X & flora) II Socio-Economic Environment 7 Impact on Landscape, Cultural Heritages and Sites of Scenic (Aesthetic) Value o Lack of harmony with natural relief & morphology X X of the landscape o Barrier leading to fragmentation of sites of X important landscape, cultural heritage or scenic value o Damage or destruction of cultural X & historical heritage o Affecting natural flow of water X 8 Land use Changes and Impacts on Traditional lifestyles and Management of Natural Resources o Loss of agricultural land X X o Loss of grazing land X X o Los of forested area X X o Loss of housing units X X o Loss of marginal land X X Item Description of key Environmental Magnitude of the Impacts Mitigation Measures No. impacts 9 Land use Changes and Impacts Significant Minor None Yes No on Traditional lifestyles and Management of Natural Resources o Increased labour force X X o Increased migration of people to X X the project area o Need of more land and X X compensation of being affected people by reduced income & lower standards of living o Induced development leading to X X growth of slum areas 10 Impact on Environmental Health o Impacts from released gases like X X Nox,HC,CO,SO2, etc. o Impacts from created conditions such as bodies of stagnant water, exotic diseases, etc. X o Impact from causes of water X X borne diseases o Impacts from produced noise X X o Impacts from created accidents during construction X X & operation phases 11 Public Resistance, Cultural Shock & Expropriation of Properties o public Resistance X X o Cultural Shock due to aggressive X X outside influences o Entailing voluntary sale or compulsory acquisition X X (expropriation) of homes & properties which causes social disruption & often economic loss for the affected people Annex 3: Standards for Industrial Pollution Control 1. TANNING AND LEATHER FINISHING Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH pH 6 – 9 BOD5 at 20oC 200 mg/l COD 500 mg/l Suspended solids 50 mg/l Total ammonia (as N) 30 mg/l Total nitrogen (as N) 60 mg/l Total phosphorus (as P) 10 mg/l Oils, fats, and grease 15 mg/l Mineral oils at oil trap or interceptors 20 mg/l Chromium (as total Cr) 2 mg/l Chromium (as Cr VI) 0.1 mg/l Chlorides (as Cl) 1000 mg/l Sulphides (as S) 1 mg/l Phenols 1 mg/l Limit Values for Emissions to Air Parameter Limit value Total particulates 50 mg/Nm3 Volatile organic carbons 75 g/m2 product produced Total hydrogen sulphide, sulphides and mercaptans (as S) 5 ppm v/v Ammonia 40 ppm v/v 40 ppm v/v Acid vapours (as HCl) 30 mg 30 mg 2. THE MANUFACTURE AND FINISHING OF TEXTILES Parameter Limit Values Temperature 40 C pH 6–9 BOD5 at 20C 50 mg/l Total nitrogen (as N) 40 mg/l COD (mg O2 /l) l 150 mg/l Total phosphorus (as P) 10 mg/l Suspended solids 30 mg/l Total ammonia (as N) 20 mg/l Oils, fats & grease 20 mg/l Phenols 1 mg/l Mercury (as Hg) 0.001 mg/l Nickel (as Ni) 2 mg/l Cobalt (as Co) 1 mg/l Lead (as Pb) 0.5 mg/l Antimony (as Sb) 2 mg/l Tin (as Sn) 5 mg/l Chromium (as Cr VI) 0.1 mg/l Chromium (as total Cr) 1 mg/l Arsenic (as As) 0.25 mg/l Cadmium (as Cd) 1 mg/l Zinc (as Zn) 5 mg/l Copper (as Cu) 2 mg/l Mineral oils (Interceptors) 20 mg/l Benzene, toluene & xylene (combined) 1 mg/l Mineral oils (Biological Treatment) 5 mg/l Organochlorine pesticides (as Cl) 0.03 mg/l Mothproofing agents (as Cl) 0.003 mg/l Organophosphorus pesticides (as P) 0.003 mg/l Adsorbable organic halogen compounds (AOX) 5 mg/l Sulphide (as S) 2 mg/l Limit Values for Emissions to Air Parameter Limit value (mg/Nm3) Particulate matter 50 50 Volatile organic carbons (as C) (excluding formaldehyde) 50 Formaldehyde 20 Isocyanates (as NCO) 0.1 3. PROCESSING OF IRON AND STEEL Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH 6–9 Suspended solids 20 mg/l Mineral oils 20 mg/l Cadmium (as Cd) 1 mg/l Mercury (as Hg) 0.01 mg/l Lead (as Pb) 0.5 mg/l Zinc (as Zn) 5 mg/l Chromium ( as Cr VI) 0.1 mg/l Chromium (as total Cr) 1 mg/l Nickel (as Ni) 2 mg/l Limit Values for Emissions to Air Parameter Limit value Particulate matter 50 mg/Nm3 Hydrogen fluoride (as HF) 5 mg/Nm3 Mercury (as Hg) 0.05 mg/Nm3 Lead (as Pb) 0.5 mg/Nm3 Zinc (as Zn) 10 mg/Nm3 Chromium (as total Cr) 0.5 mg/Nm3 Nickel (as Ni) 0.5 mg/Nm3 Cadmium (as Cd) 0.05 mg/Nm3 0.05 mg/Nm3 NOx (as NO2) 1000 mg/Nm3 1000 mg/Nm3 SOx (as SO2) 800 mg/Nm3 800 mg/Nm3 Dioxins as International Toxicity Equivalent(I-TEQ) 1 ng/Nm3 4. METAL WORKING, PLATING AND FINISHING Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH 5.5 – 9.5 Suspended Solids 25 mg/l Mineral Oil 20 mg/l Fluoride (as F) 50 mg/l Phosphorus (as P) 10 mg/l Arsenic (as As) 0.2 mg/l Cadmium (as Cd) 0.5 mg/l Cyanide (as free CN) 0.5 mg/l Chromium ( as Cr VI) 0.1 mg/l Chromium (as total Cr) 1 mg/l Copper (as Cu) 2 mg/l Lead (as Pb) 0.5 mg/l Mercury (as Hg) 0.01 mg/l Nickel (as Ni) l 1 mg/l Silver (as Ag) 1 mg/l Zinc (as Zn) 1 mg/l Total Metals 15 mg/l Trichloroethane 0.1 mg/l Trichloroethylene 0.1 mg/l Limit Values for Emissions to Air Substance Limit values Particulate matter 10 mg/Nm3 Hydrogen fluoride (as HF) 5 mg/Nm3 Mercury (as Hg) 0.05 mg/ 0.05 mg/Nm3 Lead (as Pb) 0.5 mg/Nm3 Zinc (as Zn) 10 mg/Nm3 Chromium (as total Cr) 0.5 mg/Nm3 Nickel (as Ni) 0.5 mg/Nm3 Cadmium (as Cd) 0.05 mg/Nm3 NOx (as NO2) 300 mg/Nm3 SOx (as SO2) 300 mg/Nm3 Dioxins as International Toxicity Equivalent (I-TEQ) 1 ng/Nm3 5. MALTING, BREWING, DISTILING, PRODUCTION OF WINES AND OTHER ALCOHOLIC LIQUOURS Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH 6–9 BOD5 at 20oC 60 mg/l COD 250 mg/l 250 mg/l Suspended solids 50 mg/l Total ammonia (as N) 20 mg/l Total nitrogen (as N) 40 mg/l Total phosphorus (as P) 5 mg/l Oils, fats, and grease 15 mg/l Mineral oils at the oil trap or interceptor 20mg/l Limit Values for Emissions to Air Parameter Limit value (mg/Nm3) Total Particulates (at a mass flow of 0.5 kg/h or above) 100 Hydrogen chloride (as HCl) (at a mass flow of 0.3 kg/h or more) 30 6. MANUFACTURE OF SUGAR Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH 6–9 BOD5 at 20oC 60 mg/l COD 250 mg/l Suspended solids 50 mg/l Total ammonia (as N) 15 mg/l Total nitrogen (as N) 40 mg/l Total phosphorus (as P) 5 mg/l Oils, fats, and grease 15 mg/l Mineral oils at the oil trap or interceptor 20 mg/l Limit Values for Emissions to Air Substance Limit value Total particulates (at a mass flow of 0.5 kg/h or above) 100 mg/Nm3 Hydrogen chloride (as HCl) (at a mass flow of 0.3 kg/h or more) 30 mg/Nm3 7. CEMENT MANUFACTURING Limit Values for Discharges to Water Parameter Limit Value pH 6–9 BOD5 at 20 oC 25 mg/l COD 150 mg/l Total phosphorus (as P) 5 mg/l Suspended solids 50 mg/l Mineral oils at the oil trap or interceptor 20 mg/l Limit Values for Emissions to Air Parameter Limit value Total particulates 150 mg/Nm3 Sulphur dioxide (as SO2) 1000 mg/Nm3 Nitrous oxide (as NO2) 2000 mg/Nm3 8. PHARMACEUTICAL MANUFACTURING Limit Values for Discharges to Water Parameter Limit Value Temperature 40 oC pH 6–9 BOD5 at 20 oC 50 mg/l COD 250 250 mg/l Total phosphorus (as P) 5 mg/l Total nitrogen (as N) 30 mg/l Suspended solids 30 mg/l Oils, fats, and greases 15 mg/l Absorbable organic halogen compounds (AOX) 2 mg/l 0.1 mg/l Organochlorines 0.05 mg/l Active ingredient (each) 0.2 mg/l Arsenic (as As) 1 mg/l Chromium (as total Cr) 0.1 mg/l Chromium (as Cr VI) 0. 1 mg/l Phenols 1 mg/l 2 mg/l Copper (as Cu) 0.01 mg/l Mercury (as Hg) Limit Values for Emissions to Air Parameter Limit value (mg/Nm3) Total particulates 50 50 Active ingredients 0.2 0.2 Organic compounds (Listed in Annex 1) Class I 20 Class II 100 Class III 300 Note: The industrial sectors marked purple are the sectors that will be part of the Bole lemi Industrial Zone Annex 4: Photos Album of the project site Land use of the project site Ecualyptus plantationat the project site Stone crusher plant Air pollution due to stone crushing Soil disturbance due to quarry activities Pollution load on Lemi River Lemi and Tiliku Akakai River confluence Type of house in the project site Eucalyptus trees in the project site cow dung used as source of energy for cooking at the site Building the Ethio ICT funded by bill gate Wheat farm at the project site Chickpeas farm at the project site animal rearing and farming at the project site Black Cotton soil at the heart of the project site consultation with the local community Stakeholder Consultation consultation with stakeholders Factory shed of phase one Factory shed foundation of phase one Exterior of the factory shed of phase one Construction for the provision of facilities to the proposed industrial zone Construction of internal road within the IZ Construction of factory shed foundation of phase one Construction of factory shed foundation Dist pollution due to stone crushing plants of phase one Irrigable land at the proximity of Proposed Industrial zone site Teklehymanot church at the proximity of the industrial Zone sitee Consultation meeting with affected population and their representatives Consultation meeting with affected population and their representatives Consultation meeting with project affected population Annex 5 Minutes of public consultation On the socio- economic impact assessment for the establishment of Bole Lemi phase two industrial zone Date – December 07, 2013 (November 29, 2006 EC) Venue – Bole Lemi – Gossu woreda Agenda – Public consultation on the socio-economic impact of Bole Lemi Phase II industrial zone development Attendants – 1. Ato kebede Gemeda – Public relations Officer at Woreda 11, Bole Sub city 2. Ato Teweldeberhabn Woldegerima – member of consultant team 3. Ato getcahew Abereha – member of consultant team 4. Name of community participants is attached at the end of this minutes To begin the meeting, Ato kebede explained to the community the main objective for the establishment and development of the industrial zone. He further explained that the main purpose of the meeting is to hold consultations with the project affected community the socio- economic and environmental impact of the development of the industrial zone. The consulting team has been invited to provide explanations and additional information as needed. Accordingly, one of the members of the consultant team, Ato Tekleberhan Weldegermina explained to the community: (i) The main objective of the establishment of the industrial zone (ii) The definition of industrial zones (iii) The potential benefits on both environmental and social aspects (iv) The potential adverse impacts on the community and the environment (v) Proposed mitigation measures to minimize adverse impacts and enhance positive attributes (vi) Expected cooperation and participation from the community Finally, community members were invited to express their ideas and concerns. Community members who were present at the consultation meeting raised the following main points: (1) The community supports the development of the industrial zone as it will highly contribute to economic development and job creation in the country and in the community (2) However, as their main livelihood depends on agriculture and livestock from their land located on the proposed site, during resettlement: a. The Government should provide them with convenient relocation area b. Adequate compensation to restore their livelihood c. Adequate skills training and capacity building to enable them prepare for their future d. Necessary social and economic infrastructures in the new relocation site e. Access to finance and credit to help them establish alternative livelihood The community expressed that if the aforementioned concerns are addressed, the community is willing to cooperate and do their part for the establishment of the industrial zone. The representative for the local administration has reassured the community that the administration will do its best to address all the issues raised and has closed the meeting. List of community members who participated in the consultation meeting 1. Boke Kebede 2. Tamiru Mekasha 3. Lemi Gemechu 4. Addis Gemechu 5. Sesaw kebede 6. Tsegu Balcha 7. Tabor Kebede 8. Fekadu Meskele 9. Gemechu Senbetu 10. Teshome Sudo 11. Sudo Kebede 12. Assefa Harma 13. Lema Duga 14. Alemu Areru 15. Buta Zewde 16. Tamiru Chala 17. Ashenafi Mulugeta 18. Priest Akelok Belay 19. Chala Shanko 20. Negus Tomessa 21. Mubarek Bedlu 22. Bekele Getachew 23. Kassu Hailu 24. Dachu Harma 25. Priest Beharu Getnet 26. Alemu Gutema 27. Gemechu Dego 28. Belay Gemechu 29. Fekadu Ashenafi 30. Seleshi Demis